Volt VHS-6719-25-BBZ Скачать руководство пользователя страница 6

Страница: 6 / 12

w w w . v o l t l i g h t i n g . c o m

INSTALLATION INSTRUCTIONS

- 6 -

VOLT

18” High Output Brass Rotatable LED Hardscape Light

VHS-6719-25-BBZ

Install Luminaire

Self-tapping

Screw

Luminaire

Railing, Deck
over-hang or Stair

Mark

Install from Bottom

Install from Side

Self-tapping

Screw

Luminaire

Mark

Wireway

Hole

Railing, Deck

over-hang or Stair

Wireway Hole

Glare Guard

Glare

Guard

Wall Anchor

Rubber

Washer

Install the luminaire and glare guard using provided self-tapping

screws. If the screws are difficult to install, mark holes and drill

1/8” pilot holes.

If wall anchors are required, drill proper holes from the marks on

the mounting surface and then insert the wall anchors. Then install

the luminaire and glare guard and secure them with the self-

tapping screws.

Rubber washers are required during installation from the side.

NOTE: DO NOT OVER TIGHTEN SCREWS.

Содержание VHS-6719-25-BBZ













Результаты поиска

Содержание VHS-6719-25-BBZ

Отзывы:

Похожие инструкции для VHS-6719-25-BBZ

Бренды по названию

Популярные бренды

Volt VHS-6719-25-BBZ, Руководство по установке

Результаты поиска

Содержание VHS-6719-25-BBZ

Отзывы:

Похожие инструкции для VHS-6719-25-BBZ

Бренды по названию

Популярные бренды