manualshive.com logo in svg

Volkswagen 1.9 tdi, Руководство пользователя, Страница: 37 / 67

Поделиться
Скачать
Volkswagen 1.9 tdi Скачать руководство пользователя страница 37

33

Engine Management

Engine Speed Sensor G28

The Engine Speed Sensor G28 is an
inductive sensor. It is attached to the
cylinder block.

SSP209/056

J248

SSP209/085

Engine speed sensor wheel

The Engine Speed Sensor G28 scans a
60-2-2 sensor wheel attached to the
crankshaft. This means that the sensor
wheel has 56 teeth with two gaps the width
of two teeth each on its circumference.

These gaps are 180 degrees apart and
serve as reference points for determining
the crankshaft position.

Signal application

The signal generated by the Engine Speed
Sensor G28 provides both the engine speed
and the exact position of the crankshaft.

The injection point and the injection quantity
are calculated using this information.

Effects of signal failure

If the signal of the Engine Speed Sensor
G28 fails, the engine is switched off.

Electrical circuit

G28

Engine Speed Sensor

J248 Diesel Direct Fuel Injection Engine

Control Module

SSP209/057

G28

Содержание 1.9 tdi




































































Отзывы:

Нет отзывов