Volkswagen 1.9 tdi Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 67

Volkswagen 1.9 tdi Скачать руководство пользователя страница 34

30

Sensors

Camshaft Position Sensor G40

The Camshaft Position Sensor G40 is a
Hall-effect sensor.

It is attached to the toothed-belt guard
below the camshaft gear.

It scans seven teeth on the camshaft sensor
wheel attached to the camshaft gear.

Signal application

The Diesel Direct Fuel Injection Engine
Control Module J248 uses the signal that
the Camshaft Position Sensor G40
generates to determine the relative
positions of the pistons in the cylinders
when starting the engine.

Effects of signal failure

In the event of Camshaft Position Sensor
G40 signal failure, the Diesel Direct Fuel
Injection Engine Control Module J248 uses
the signal that the Engine Speed Sensor
G28 generates.

Electrical circuit

G40

Camshaft Position Sensor

J248 Diesel Direct Fuel Injection Engine

Control Module

J317 Power Supply (Terminal 30, B+) Relay

Engine Management

Camshaft
Sensor Wheel

SSP209/054

Camshaft Position
Sensor G40

SSP209/055

J248

G40

J317

S

«
...
32
33
34
35
36
...
»

Содержание 1.9 tdi




































































Отзывы:

Нет отзывов