Void KRYO K4 Скачать руководство пользователя страница 9

Page 9

Kryo 

 Series Power Amplifiers

acoustics

System Connections

Dual Mode

In dual mode connect individual sources to inputs A and B and set the link / dual 
switch to dual. Channel A's input will output from out A, channel B's input will 
output from out B. Out A and out B use pins +1,-1 or you can connect to out A/B 
with 4 core cable, where pins +1,-1 are for channel A and pins +2,-2 are for 
channel B. This type of arrangement could be used for 2 way active speakers, 
where channel A would be bass and channel B would be HF. If 4 core speaker 
cable was used then the speaker would be connected from out A/B. Note, this 
arrangement would only work if the speakers were wired pins +1,-1 to the 
woofer and pins +2, -2 to the HF unit.

Link Mode

If the link / dual switch is set to link, then channels A and B will receive the 
same signal. This mode is useful if you only have 1 input source but want to 
feed both amplifier channels. Typical arrangements could be powering 2 speakers 
from a mono output, in which case you would connect the mono source to input 
A and set the link switch to link. The same signal will now appear at both out A 
and Out B. 

Bridge Mode

In bridge mode channels A and B are combined to form one channel. To enable
bridge mode set the dip switches to bridge and use input A. The link / dual switch 
should be set to dual and use out A/B for the output. Connect to pins +1 and +2.
Pin +1 is . Note that the minimum impedance in bridged mode is 4 ohms.

Содержание KRYO K4

















Отзывы: