Void ARCLINE 6, Руководство пользователя

Страница: 9 / 10

Getting Started
1. Carefully unpack all the speaker cabinets.
2. Place an Arcline X into its desired position and place another Arcline X on top. Insert the winch up tower though
both Arcline X subs making sure the winder handle faces rearwards. Next mount the craddle on to the top of the
winch up stand. Extend the front mounting bars and insert the locking pins on one of the Arcline 6 enclosures. Lift
the Arcline 6 on to the cradles bottom bar then lift the Arcline 6 until both front mounting bars are lined up with the
cradles front mounting points. Insert both locking pins. Fit the rear mounting bar, adjust the tilt and then insert the
locking pins. If a single Arcline 6 is to be used in a craddle, insert 2 locking pins into the cradles telescopic tubes. If
a further Arcline 6 is to be used, push the Arcline 6 up vertically until the telescopic tubes are fully extended and
insert both locking pins. A further Arcline 6 can now be mounted under the top Arcline 6 by use of the mounting bars
and locking pins.
3. (Connection Method 1. Using two Infinite 8's (X or V2 models) and the cables supplied in the accessory pack)
Each side of the system uses one amplifier. The connections for both left and right sides are identical. Connect the
outputs of a Digidrive to the inputs of an amplifier. CH 1 on the amplifier will be bass and CH 2 will be mid hi. Connect
one of the thick (4 way) 8 meter speaker cables to output CH 1 on the amplifier. Connect the other end of this cable to
one of the speakons on the bottom Arcline X. Both speakons on an Arcline X are wired in parallel, so you can connect
to either speakon. Link from the bottom to top Arcline X sub by using the 1 meter (4 way) link cable. Use the 3 meter
(2 way) cable to connect from the top Arcline X to the speakon marked INPUT on the Arcline 6. Repeat the same
connections for the other side of the system.
(Connection Method 2. Using separate amplifiers for Arcline X and Arcline 6 and an adaptor cable)
This connection method use's the same connections as method 1, but requires an adaptor to be made to connect the
outputs of both amplifiers into the 4 way cable. The adaptor is made from two speakon plugs and one speakon
socket. Wire a short length of cable to pins +1 and -1 on a speakon socket. The other end of this cable gets attached
to a speakon plug wired +1, -1. Wire another short length of cable to pins +2, -2 on the speakon scoket. The other
end of this cable gets attached to a speakon plug wired +1, -1. The plug wired +1, -1 should be connected to the
bass amplifier and the plug wired +2,-2 should be connected to the mid hi amplifier. The speakon socket should be
connected to the end of the think (4 way) 8 meter cable that would normally be connected to CH 1's output on an
Infinite 8.
(Connection Method 3. Using separate amplifiers for Arcline X and Arcline 6)
Connect one of the thick 8 meter speaker cables to one channel of the bass amplifier. Connect the other end of this
cable to one of the speakons on the bottom Arcline X. Both speakons on an Arcline X are wired in parallel, so you
can connect to either speakon. Link from the bottom to top Arcline X subs by using the 1 meter link cable. Use a 10
meter cable (not supplied) wired +1, -1 to +1, -1 and connect one end to the mid hi amplifier. Connect the other end
to the speakon marked INPUT on the Arcline 6. Repeat the same connections for the other channel of the
system.
4. When using two Arcline 6's per side, link via the LINK OUT and INPUT speakons on the rear of the Arcline 6's with a
2 way cable wired +1, -1 to +1, -1.
Precautions
Only connect an Arcline 6 to an Arcline X with a cable wired +2, -2 to +2, -2. If a cable wired +1, -1 to +1, -1 is
used the Arcline 6 will receive the same signal as the Arcline X.
Warranty Registration
Please take time to fill out the warranty registration form at the back of the manual and return it to Void Acoustics
Arcline 6