background image

Important Safety Instructions

1

Important Safety Instructions

When using your telephone equipment, basic safety precautions
(including the following) should always be followed to reduce the risk of
fire, electric shock, and injury to persons.

†

Read and understand all instructions.

†

Follow all warnings and instructions marked on telephone.

†

Do not use liquid cleaners or aerosol cleaners on the telephone; use a damp
cloth for cleaning.

†

Do not operate the telephone near water (i.e., near a bath tub, wash bowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool).

†

Do not place this telephone on an unstable cart, stand, or table. The
telephone may fall causing serious damage to the telephone.

†

Slots and openings on the bottom of the telephone are provided for
ventilation to protect it from overheating. These openings must not be
blocked or covered. The openings should never be blocked by placing the
telephone on the bed, sofa, rug, or other similar surface. This telephone
should never be placed near or over a radiator or heat register. This telephone
should not be placed in a built-in installation unless proper ventilation is
provided.

†

Never push any objects into this telephone through slots as they may touch
dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never pour any liquids on the telephone.

†

To reduce the risk of electric shock, do not disassemble this telephone. Take
the telephone to a qualified serviceman when service or repair work is
needed. Opening or removing covers may expose you to dangerous voltage
or other risks. Incorrect reassembly can cause electric shock when the
appliance is subsequently used.

†

Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.

†

Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVE THESE INSTRUCTIONS

Содержание STARPLUS 2700 Series





































Отзывы: