Vladimir's Models Snipe Скачать руководство пользователя

Страница: 1 / 12

Snipe
Recommendations for assembly

The list of parts and materials to build:

Accessory kit: Parts set:

1 - Horns wing (2 pcs);

2 – Launch T peg;

3 – Ballast nose mount;

4 - Stabilizer control horn (with slot)

5 – Vertical tail control horn (with hole);

6 - Torsion spring rudder and elevator;

7 - Screw for ballast M3;

8 - Screws stabilizer (2 pieces);

9 - Spare screws stabilizer (2 pieces);

10 - Set of screws for attaching the wing and M3 h10 M3x6
(1 set of spare);

11 - Cover wing controls;

12 - Pipes for sealing control cables;

13 – Flaperon control horn pivot axes.

1 - Wing;

2 - Accessory Kit Snipe;

3 – Flaperon pushrod (2 pieces);

4 – Flaperon pushrod housing;

5 - Fuselage;

6 – Flaperon pushrod stiffener plate;

7 - Stabilizer;

8 – Vertical tail.

List of recommended hardware to run your model:

1) ballast Snipe;

2) battery Shread-RC Smart Li-Po 650mAh or Shread-RC Smart Li-Po 450 mAh

3) Servos: JR 285 MG, FutabaS3155, MKS-DS6100, HyperionDS09-SCD, DymondD60; DymondD47 (Only the rudder);

4) receivers: Spectrum AR6255; Futaba 6008HS without the case; Futaba R6106HFC; Weatronic Clever 6 Receiver 2.4 Dual FHSS.

The list of materials needed to build the model:

superglue and liquid medium, the accelerator

Cutter

Masking tape

4) Pen and ruler

5) Pliers

6) Sandpaper number 240-320

Содержание Snipe













Результаты поиска

Содержание Snipe

Отзывы:

Похожие инструкции для Snipe

Бренды по названию

Популярные бренды

Vladimir's Models Snipe, Рекомендации по сборке

Результаты поиска

Содержание Snipe

Отзывы:

Похожие инструкции для Snipe

Бренды по названию

Популярные бренды