Vivotek IT9389 Series Скачать руководство пользователя

Страница: 72 / 395

VIVOTEK

72 - User's Manual

Please follow the steps below to set up a profile:

1. Select the

Profile mode

tab.

2. Select the applicable mode: Night mode or

Schedule mode. Please manually enter a range of

time if you choose the Schedule mode.

3. Configure Exposure control settings in the folowing

columns. Please refer to previous dicussions for

detailed information.

4. Click

Save

to enable the setting and click

Close

exit the page.

You can click

Restore

to recall the original settings without incorporating the changes. When

completed with the settings on this page, click

Save

to enable the settings.

If you want to configure another sensor setting for day/night/schedule mode, please click

Profile

open the Profile of exposure settings page as shown below.

Activated period: Select the mode this profile to apply to: Day mode, Night mode, or Schedule

mode. Please manually enter a range of time if you choose Schedule mode. Then check

Save

take effect.

Note that the Profile mode is

not

available when the

IR cut filter

setting is configured into the Auto

mode.

Содержание IT9389 Series












































































































































































































































































































































































































Результаты поиска

Содержание IT9389 Series

Отзывы:

Похожие инструкции для IT9389 Series

Бренды по названию

Популярные бренды

Vivotek IT9389 Series, Руководство пользователя

Результаты поиска

Содержание IT9389 Series

Отзывы:

Похожие инструкции для IT9389 Series

Бренды по названию

Популярные бренды