background image

Thermostat Quick Reference

4

Battery Door Information

5

Thermostat Quick Reference

Insert 2 AA 

Alkaline batteries 

(included). High 

quality alkaline 

batteries are 

recommended.

Located ont he back of the thermostat.

The low battery indicator is displayed when the AA battery 

power is low. If the user fails to replace the battery within 21 

days, the screen will only show the low battery indicator but 

maintain all functionality.  If the user fails to replace the batteries 

after an additional 21 days (days 22-42 since first “low battery” 

display) the setpoints will change to 55˚F (Heating) and 85˚F 

(Cooling). If the user adjusts the setpoint away from either of 

these, it will hold for 4 hours then return to either 55˚F or 85˚F.  

After day 63 the batteries must be replaced immediately to 

avoid freezing or overheating because the thermostat will shut 

the unit off until the batteries are changed.

Important:

If your HVAC contractor has configured the thermostat to remind you when 

the air filter needs changed, you will see 

FILT 

in the display when your air 

filter needs to be changed.

 

Resetting The Filter Change Reminder: 

When 

FILT

 reminder is displayed, 

you should change your air filter and reset the reminder by holding down

the second button down from the top left of the thermostat for 3 seconds.

Filter Change Reminder

 

When the 

R250S

 is used as an outdoor sensor and a dual fuel balance point 

   is enabled, an outdoor temperature above balance point will cause the 

   thermostat to only allow Y terminal(s) to energize. An outdoor temperature

   below balance point will cause the thermostat to only allow the W2 to 

   energize.

• The temperature shown is the average of all remotes, when using 

R251S

 

   indoor sensors.

• When using the 

R250S

 as a floor sensor, High Limit may cause system to be 

   off even when temperature isn’t yet satisfied. This is to avoid heating 

   beyond setpoint.

Remote Information 

When the battery icon             appears replace your AA batteries 

immediately. Failure to do so may result in your heating & cooling 

system becoming inoperable.  Freezing or overheating can occur.

 

Caution:

Содержание TP-S-755










Отзывы: