Vivax ACP-07CH21ZNLO Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 39

background image

INSTALLATION

Connecting
cable

Outdoor unit terminal

1

Wiring

1 Remove the self-tapping screws (2 pcs)
on the maintenance board and take out the
maintenance board.

Maintenance
board

Terminal board

Fix the cable wire
with anchor cable

Piping cover

Please utilize outdoor pipe support when
the cable wire is led from the backside.

Outdoor pipe support
(Outdoor pipe support is not required
when leading the cable wire from other places).

The cable wire can be led from the back hole
of the piping hole or ejecting hole.

Maintenance
board

Piping cover Ejecting hole

Right wiring

Back wiring

Sponge

Piping cover

2 Loosen the self-tapping screws (2 pcs) on
the fixing clip to loosen the fixing clip.

5 Install the maintenance board. After the pipes
and cable wire are installed, please seal the
sponge block as per drawing indication.

3 Loosen the fixing screw of the wire terminal
board, pass the power wire and signal wire
through the fixing clip. Then firmly fix the
power wire and signal wire on the terminal
board with the fixing screw. (Earth wire
must be connected firmly.)

4 Tighten the self-tapping screw on the fixing clip.

Wiring For

Above 6000W Model (Above 21000BTU/h Model)

Connecting
cable

Outdoor unit terminal

or

Installation diagram of indoor unit and outdoor unit

7

«
...
6
7
8
9
10
...
»

Содержание ACP-07CH21ZNLO








































Отзывы:

Нет отзывов

Похожие инструкции для ACP-07CH21ZNLO

Room Air Conditioner

Бренд: Napoleon Страницы: 30

IAQ 1" Polarized Media Air Cleaner

Бренд: EnviroAire Страницы: 4

Бренд: AiroDoctor Страницы: 8

GJC12AG-E6DRNB9A

Бренд: Gree Страницы: 50

Бренд: Daewoo Страницы: 131

Бренд: York Страницы: 44

Бренд: Sakura Страницы: 16

Бренд: Daikin Страницы: 65

GWH09ACC-S6DBA1A/O

Бренд: Gree Страницы: 123

Бренд: BEEWAIR Страницы: 20

FAVORITE ON-OFF Series

Бренд: Roland Страницы: 80

Бренд: Haus & Luft Страницы: 35

Бренд: SPT Страницы: 24

Бренд: ActivePure Страницы: 2

SkyAir RZQ-P Series

Бренд: Daikin Страницы: 238

Бренд: Goodman Страницы: 14

Euro-Line AS28AL

Бренд: Argo Clima Страницы: 32

Бренд: Midea Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды