Hydraulic oil tank
→
Hydraulic pump
1.
Place the hydraulic hose (17) in the hydraulic oil tank
connection accessory (4);
2.
Put the screw hose clamp and tighten the fixing screw;
3.
Place the hydraulic hose on the hydraulic pump
connection accessory (3);
4.
Put the screw hose clamp and tighten the fixing screw;
Hydraulic pump
→
Control valve handle
5.
Screw the hose nut (13) into the connection thread of the
hydraulic pump (3);
6.
Screw the hose nut with into the connection thread of
the control valve handle (23);
Control valve handle
→
Hydraulic oil tank
7.
Screw the hose nut with into the connection thread of
the control valve handle (23);
8.
Screw the hose nut with into the connection thread of
the hydraulic oil tank (4).
1.
Turn off the air suction valve, move the choke lever (38)
until it is left placed;
2.
Open the fuel tap (37), the lever should be right placed;
3.
Set the throttle lever (39) to 1/3 of the distance between
positions from the right;
4.
Turn the "ON/OFF" switch (29) to the "ON" position;
5.
5.Pull the starter cord (19) slowly until you feel some
resistance, then pull hard until the engine starts;
6.
After about 30 seconds, turn on the air suction valve,
move the choke lever to the right.
Do not turn off the air suction valve if the engine is
warm or the air temperature is high.
1.
Place the throttle lever (39) to the right;
2.
Set the "ON/OFF" switch (29) to the "OFF" position”;
3.
Turn off the fuel tap (37), the handle should be left
placed.
In case of emergency, immediately place the
"ON/OFF" switch to the "OFF" position”
.
The engine operating speed is adjusted by the throttle lever
(39).
With the throttle lever on the right, the engine runs idle. The
speed increases as the lever is moved to the left.
The full-length beam can be placed in 3 different positions,
horizontal, inclined and vertical.
For larger logs use the vertical position.
1.
Place the full-length beam (6) in the desired position;
2.
If you want to use the inclined or vertical position,
remove the log holder (2) from the base (1);
3.
Adjust the beam fixing lever (5) to the notch associated
with the defined position and tighten the fixing screw.
1.
Place the log on the full-length beam (6) or on the log
holder (2), inside the log catcher (25);
2.
Press both control valve handles (24) simultaneously
into the direction you want to split;
3.
After splitting the log, press the control valve handles in
the opposite direction simultaneously to perform the
wedge recoil.
The log splitter engine is ready to run with petrol. Never use
contaminated petrol or other types of fuel. Avoid the
presence of dirt or water in the tank (32). Otherwise,
problems may arise with the fuel pump and injectors.
To check the fuel level and fill the tank, the engine must be
stopped. When filling the fuel tank, do not exceed the
maximum level, the upper limit of the filter.
Содержание VIRLG12
