Vitesse VSC8228 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 13

Vitesse VSC8228 Скачать руководство пользователя страница 10

VSC8228 Evaluation Board

Software / User Usage Guide

Applications Engineering

____________________________________________________________________________

________________________________________________

10 of 13

_______________________________________________

Rev 1.0

Confidential

01/25/05

d) Verifying the connection between the PC and evaluation board using RS-232 Port (TWSI):

The software default for the serial port is

COM1

with

TWSI

address

0x8E

. The

Message Window

located at the

bottom of the register window provides various notification and error messages. If the Message Window indicates
that the microcontroller did not respond or serial port is incorrect then try a different COM port by selecting one in
the Options dialog box. The Options dialog is activated by selecting “

View

Æ

Options

” from the program menu or

by click on the “

OpenOption.txt

” script, which will open the

Options

window as shown below:

If the PC software is able to communicate with the microcontroller, it will display the firmware version. This
confirms that the PC is communicating with the board and then you can close the Options dialog box.

Message Window

«
...
8
9
10
11
12
...
»

Содержание VSC8228














Отзывы:

Нет отзывов