Vitek VT-8471, Инструкция по эксплуатации

Страница: 10 / 40

10
ENGLISH
lacking experience or knowledge if they are
not under supervision of a person who is
responsible for their safety or if they are not
instructed by this person on the usage of
the unit.
•
Do not use the unit if the coffee maker body,
the power cord or the power plug is dam-
aged.
•
If the power cord is damaged, it should be
replaced by the manufacturer, a maintenance
service or similar qualified personnel to avoid
danger.
•
Do not repair the unit by yourself. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and contact any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.vitek.ru.
•
Transport the unit in the original packaging
only.
• Keep the unit in a dry cool place out of reach
of children and people with disabilities.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
–
Take the coffee maker out of the package and
remove the packaging materials.
–
Check the unit for damages; in case of dam-
ages do not use the unit.
–
Make sure that operating voltage of the cof-
fee maker corresponds to the voltage of your
mains.
BEFORE USING THE UNIT
•
Make sure that the steam supply is closed. To
do this turn the knob (4) «OFF--- +» clockwise
until bumping «OFF».
•
Before the first use of the coffee maker wash
all the removable parts (3, 11, 12, 18) with
warm water and dry them.
•
Before switching the unit on, make sure that
the mains voltage corresponds to the voltage
specified on the unit body.
•
Remove the water tank (3), fill it with cold
water up to the MAX mark and install it back
to its place.
•
Insert the coffee filter (11) into the holder (12).
•
Install the filter holder into the coffee maker.
The holder (12) ledges should match the
grooves on the boiler «
», after that turn
the filter holder handle (14) to the right until
bumping «
».
•
Place a suitable cup on the tray (8) grid (9).
•
Insert the power plug into the mains socket.
•
Switch the coffee maker on by pressing the
on/off button (15) «ON/OFF», the button (15)
illumination will light up and the button (16)
illumination will start flashing.
•
Wait until the water supply button (16) illumi-
nation glows constantly. The coffee maker is
ready for operation.
•
To fill the boiler with water press the but-
ton (16), wait for 15-20 seconds, or at the
first signs of appearance of water in the cup,
switch the water supply off by pressing the
button (16) again.
Notes:
Filling the boiler with water is necessary for
removing the air block when you switch the cof-
fee maker on for the first time.
•
Press the water supply button (16) and wash
the boiler.
•
Depending on the cup capacity repeat this
procedure several times until the boiler is
clean.
ATTENTION!
–
Do not remove the filter holder (12) if the but-
tons (16), (17) are pressed.
–
Do not remove the filter holder (12) immedi-
ately after preparing coffee as there is redun-
dant water and steam pressure inside, let the
coffee maker cool down completely.
–
To remove the filter holder (12) turn the han-
dle (14) to the left «
» and remove the filter
holder (12).
MAKING ESPRESSO
•
Make sure that the steam supply is closed. To
do this turn the knob (4) «OFF--- +» clockwise
until bumping «OFF».
•
Make sure that there is enough water in the
water tank (3). If necessary, add water but do
not exceed the MAX mark.
•
Insert the coffee filter (11) into the holder (12).