Vitek VT-8214, Инструкция по эксплуатации

Страница: 4 / 24

4
ENGLISH
•
For children safety reasons do not leave poly-
ethylene bags used as packaging unattended.
Attention! Do not allow children to play with poly-
ethylene bags or packaging film. Danger of suf-
focation!
•
Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any malfunc-
tion is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
• Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
USING THE HAIRDRYER
After unit transportation or storage at low
temperature it is necessary to keep it for at
least three hours at room temperature before
switching on.
•
Unpack the unit completely and remove any
packaging materials that can prevent the unit
operation.
•
Unwind the power cord completely.
• Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit operating voltage.
• Insert the power plug into the mains socket.
Switching hair dryer on
Before switching the appliance on make sure power
supply voltage meets operating voltage of the ap-
pliance.
• Insert power cord plug into wall outlet.
• Select operating speed you need using airflow
speed switch (1):
0 = the hairdryer is switched off;
= low speed;
= high speed;
• Select airflow temperature you need using heat-
ing degree switch (2).
= slight heating
= medium heating
= maximal heating
= cool shot button, press the cool shot button
to fix your hairstyle, then press the button again
for hor air supply.
Taking care about your hair
Before drying and setting your hair, wash them with
shampoo, dry with towel to remove excessive mois-
ture and brush for better results.
Fast drying
Set switch (2) into position of maximal heating
(position ), select airflow speed you need using
switch (1) and dry your hair out a little bit. Shake off
excessive moisture by hand or using a brush and
continuously move the hair dryer over your hair.
Straightening your hair
Set switch (2) into position of maximal heat-
ing (position ), select airflow speed you need
using switch (1) and dry your hair out a little
bit. When your hair are almost dry, install concen-
trating nozzle (4), reduce degree of air heating by
switch (2) and airflow speed by switch (1).
Divide your hair in locks and layers, and start
straightening them from lower layers upwards.
Bruch hair downright using round or flat brush,
simultaneously directing hot air blowing from con-
centrating nozzle on them. Straighten each lock
from root to tip this way. After you have finished
straitening locks of the lower layer, start process-
ing the locks of medium layer, and so on, and finish
with straitening locks of the upper layer.
Natural waving structure of your hair
Set switch (2) into position of slight heating (posi-
tion ), then set switch (2) into position , hold a lock
between your fingers tightly, turn it to direction of its
natural curliness, then dry the lock out by directing air
jet between the fingers. After getting the shape you
need, press cool shot button (2) and fix each lock.
Rising up and volume
Using hair dryer in any mode of heating/any speed
from slight to maximal, dry out hair roots beginning
from backside of your head.
Styling your hair
Set switches (1,2) into positions of slight heating
and slow speed correspondingly, attach concen-
trating nozzle (4) to provide directed airflow.
Divide your hair into locks and start creating hair-
style you need using round brush for setting hair.
While styling, direct airflow straight on your hair in
any direction you want.
If necessary, direct air jet on each lock for 2-5 seconds
to fix it. Time of setting locks you should determine on
your own taking into account type of your hair.
IM VT-8214.indd 4 28.02.2018 11:54:22