Vitek VT-3526 BK, Инструкция по эксплуатации

Страница: 6 / 32

6
ENGLISH
•
To switch the alarm sound signal off, press the
button (13) « ».
Note
The alarm/radio signal will sound during 30
minutes if you do not press any buttons.
Display brightness setup
•
Set up the necessary display brightness by
pressing the button (1) «SNOOZE/SLEEP/
DIMMER» repeatedly in the current time mode.
Sequential displaying mode
You can switch on the sequential displaying of
current time, year and current date.
•
To activate this function in the time mode (radio
is off), press and hold the button (11) «
D » until
the symbol «on» appears on the display.
•
To switch the sequential displaying mode off,
press and hold the button (11) «
D » until the
symbol «OFF» appears on the display.
Radio stations reception
• Connect the unit to the mains and press the
button (13) « ».
• Use the buttons (8) «◄◄» and (9) «►►» for
tuning to the desired radio station.
Manual tuning: consequently press the buttons
(8)
« ◄◄ »
and (9)
« ►► »
to select the desired
radio station with step of 0.1 MHz in FM mode.
Auto tuning: press and hold the button (8)
« ◄◄
»
or (9)
« ►► »
for more than 2 seconds. The tuner
shall begin scanning and automatically stops after
finding the closest strong radio station signal.
•
To switch the radio off, press the button (13)
«
».
Antenna (22)
Select the wire antenna (22) position for quality
reception of the radio signal.
Volume level adjusting
Use buttons (10) and (11) to set the desired volume
level.
Radio stations programming
You can set up and save settings for 10 radio
stations in FM band.
• Tune to the station you want to program.
• Press and hold the button (12) «NAP/M+/
MEM/
¹ » until a flashing symbol of «Р01»
appears.
• Consequently press the buttons (8) «◄◄» or
(9) «►►» to select the number of the program -
ming cell.
•
Press the «NAP/M+/MEM/ ¹ » button (12) again
to save settings.
•
Repeat steps 1-4 for all radio stations which you
wish to save in the clock radio memory.
•
To select one of the pre-programmed radio sta-
tions, press the button (12) «NAP/M+/MEM/
¹ »
in radio mode consequently.
Sleep timer
You can set up the radio switch off time.
•
Press the button (1) «SNOOZE/SLEEP/
DIMMER» in radio mode. The symbols «90» will
appear on the display, which means automatic
switching off in 90 minutes.
•
Set up the necessary auto switch off time (90,
60, 30 or 15 minutes) by pressing the button (1)
«SNOOZE/SLEEP/DIMMER» repeatedly.
•
To cancel this function, press the button (1)
«SNOOZE/SLEEP/DIMMER» repeatedly until
the «OFF» symbol appears on the display or
switch the radio off by pressing the button (13)
« ».
Notes
Electromagnetic interference can influence
operation of the unit. In this case disconnect the
unit from the power sources, and then connect
again.
If necessary move or relocate the unit.
Display auto switch off
•
To activate this function, press and hold the but-
ton (10) until the indicator (4) « » appears. The
display will be automatically switched off in 15
seconds after pressing any button.
Note: This function is inactive in the radio mode.
•
To switch the function off, press and hold the
button (10), the indicator (4) goes out.
Countdown timer
• Pre
ss the button (12) «NAP/M+/MEM/ ¹ » in
the current time mode, the symbol «n90» will
appear on the display, which means countdown
timer actuation in 90 minutes.
• S
et the timer actuation time from 10 to 90 min-
utes with a 10 minute step by pressing the but-
ton (12) «NAP/M+/MEM/
¹ » repeatedly.
• To
view the remaining time, press the button
(12) «NAP/M+/MEM/ ¹ » once.
VT-3526.indd 6 19.02.2014 17:19:02