6
ENGLISH
person’s shoulders with a towel and comb
his/her hair with the comb (14).
– Switch the unit on by pressing the button (3).
Reminder
•
Cut off a little amount of hair at a time; if nec-
essary, you can always return to the cut area
again for additional cutting.
•
Comb hair with the comb (14) to reveal
uneven locks.
•
It is better to leave longer hair after cutting
for the first time.
•
After learning the unit better, you will be able
to arrange your hair in any style you need.
Step one
Set the attachment comb (6) to position “3” or
“6”. Switch the hair clipper on by pressing the
button (3). Hold the unit with the blades pointed
upwards. Start cutting from the lower part of
the head. Slowly move the clipper upwards. Cut
all hair on the back bottom part of the person’s
head and near the ears (pic. 1, 2, 3).
Step two
Switch the hair clipper off using the button
(3), set the attachment to position “9” or “12”,
switch the hair clipper on and continue cutting
hair near the top of the head (pic. 4).
Step 3 – cutting temples
Switch the hair clipper off, set the attachment to
position “3” or “6”, and cut hair on the temples.
Then set the attachment to position “9” or “12”
and continue cutting towards the top of the
head.
Step 4 – cutting the top of the head
Using the attachment comb in position “9”
or “12”, cut the hair from the top of the head
towards the crown against the hair growth
direction.
•
You can cut hair both against and along the
hair growth direction, but keep in mind that
hair cutting against the growth direction will
be shorter than the hair cut along it.
•
Set the attachment comb (6) to position “3”
и “6” for very short haircut. Use the attach-
ment (7) to leave longer hair.
•
To leave longer hair, take hair locks between
your fingers and cut hair using the hair clip-
per (pic. 5).
•
You can use the comb (14): lift the hair locks
and cut them above the comb (pic. 6).
•
Always start cutting from the back of the
head.
•
Comb hair with the comb (14) to reveal
uneven locks.
•
Use the scissors to trim hair.
Step 5 - the final part
In the final stage of hair cutting remove the
attachment comb, turn the blades of the hair
clipper towards the hair and carefully trim hair
on the temples and neck (pic. 7). Do not press
the clipper strongly, there is danger of injuries
or cuts when open blades come in contact with
skin.
Cone-shaped haircut
Install the necessary attachment comb and
start cutting from the back of the head towards
the crown. Cut hair against hair growth from the
front of the head to the crown and on the head
sides (pic. 8). To get a flat top haircut, use the
comb (14): lift the locks and cut them along the
comb. Comb hair with the comb (14) to reveal
uneven locks.
Thinning out function
Thinning out is cutting of separate locks. It
provides smooth transition between the locks
of different length. Thinning out is made at the
final cutting stage.
– To pull the thinning comb out, move the
clamp (4) to the left till bumping, to remove
the thinning comb, move the clamp (4) to the
right till bumping.
CLEANING AND CARE
– Switch the hair clipper off after you finished
using it.
– Clean the unit body and base with a soft,
slightly damp cloth, and then wipe them dry.
– Do not immerse the hair clipper, blade block,
power adapter into water or other liquids.
– Detach the attachment from the unit body.
Remove the remaining cut hair from the out-
side and inside of the attachments with the
cleaning brush (13).
– You can wash the attachments under a water
jet, then wipe them dry.
VT-2542.indd 6
12.09.2013 17:09:32
