Vitek VT-1762, Инструкция по эксплуатации

Страница: 5 / 46

• Do not disassemble the unit yourself, if any
malfunction is detected, address the nearest
authorized service center.
• Regularly clean the unit; do not allow cracks
to appear on the sprayer.
• Keep the unit out of reach of children.
FOR HOUSEHOLD USAGE ONLY
Using the humidifier
Unpack the unit and remove the packing materi-
als. Examine the unit for damages. Do not switch
on the unit if there are any damages in it. Place
the unit on the flat stable waterproof surface.
Note:
- if the unit was subjected to negative
temperatures, before switching it on for the
first time, keep it at room temperature for 30
minutes.
- use the unit at temperature starting from +5
, and relative humidity less than 80%.
- water temperature in the water tank (15)
should not 40°С.
1. Take the handle (12) and remove the water
tank (15) from the body (8).
2. Turn over the tank (15); unscrew the lid (18),
by turning it anti clockwise. Fill the water tank
(15) with necessary quantity of water and
screw the lid (18), by turning it clockwise.
Note:
- do not fill the water tank (15) full, to avoid
splashing of water when screwing the lid
(18) with the filter-cartridge (17).
3. Set the filled tank (15) on the body of the unit
(8). Wait for some time, which is necessary
to fill the operating chamber of the “sprayer”
(10) with water.
4. Plug in the humidifier, you will hear a sound
signal, the indication (9) will appear on the
display (1); the value of humidity (29, 30) will
be displayed.
5. Switch on the humidifier, by pressing the
(3) “ON/OFF” button, the display will switch
to full brightness and the steam intensity
indication (31) will light up and the mood
lighting (2) will switch on.
6. Press the (5) “+/-“buttons to set the
“smog” intensity: 1, 2, 3, the corresponding
indication (31) will appear on the display (1).
Note:
-
each pressing of the control buttons will be
accompanied with a signal.
- if no button has been pressed during 30
seconds on the control panel or on the
remote control, the mood lighting will go
out, the display brightness will decrease
automatically in 30 seconds after pressing
any button.
7. Press the (7) “NIGHT- LIGHT” button to witch
on the mood lighting, press the (7) “NIGHT-
LIGHT” button again, the mood lighting (2)
will go out.
8. To switch on the ionization mode, press the (4)
“OZONE” button, the indication (26) will appear
on the display (1). To switch off the ionization
mode, press the (4) “OZONE” button once
again, the indication (26) will go out.
9. To switch on the automatic humidity
maintenance mode, press the (6) “SETUP”
button, the indication “Auto” (28) will be
flashing on the display (1), press the (5)
“+/-“ button to set the required humidity in
the room (from 45 to 90%, setting step is
5%). In the automatic humidity maintenance
mode the indication “Auto” (28), digital value
of the room humidity (29) and the “smog”
intensity (31) will appear on the display (1).
In automatic mode “smog” output intensity
will change and it will be reflected on the
display (1) when the preset humidity is be
reached, the unit will switch off, when the
humidity decreases, the humidifier will
switch on again.
10. To view the preset humidity value press
the (6) “SETUP” once, value of the preset
humidity will appear on the display (1), in 5
seconds the information on the display will
return to the previous mode.
11. To switch off the automatic humidity
maintenance mode, press the (6) “SETUP”
button, press the (5)
“+/-“button the required
number of times , when the humidity value
passes 90%, the indication (28) “Auto” will
go out.
5
ENGLISH
VT 1762_Instr.indd 5 VT 1762_Instr.indd 5 22.06.2011 17:22:57 22.06.2011 17:22:57