Vitek VT-16P250WS Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 30

Vitek VT-16P250WS Скачать руководство пользователя страница 4

VT-16P250WS / VT-24P370WS: 16 / 24 Port L2 Web Smart Ethernet PoE Switch

3

Link/Act LED:

Green (for megabit ports): Indicates that the port is running at 100M.
Green (for gigabit ports): Indicates that the port is running at 1000M.

Blinking: Indicates that the switch is either sending or receiving data to the port.

Light off: No link.

PoE LED:

Green: Indicates the PoE powered device (PD) is connected and the port supplies power successfully.

Light off: Indicates no powered device (PD) connected.

Reset:

By pressing the Reset button for 5 seconds the switch will change back to the default configuration and all

changes will be lost.

2.3 Rear Panel

The rear panel view of the switch consists of an AC power connector, Power Switch and Fuse.

3

Hardware Installation

3.1 Package contents

Package contents include the following:

n

PoE Switch: 16x10/100 PoE ports with 2x10/100/1000 combo ports Ethernet Switch

n

AC power cord

n

Two (2) rack-mount ears and Six (6) screws

n

Four (4) adhesive-backed rubber feet

n

User’s manual

IMPORTANT:

If any piece is missing or damaged, please contact your local dealer or reseller for service.

3.2 Switch Installation

Desktop or Shelf Installation

When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached on the
bottom at each corner of the device’s base. Allow enough ventilation space between the device and the objects
around it.

Note:

Do not press on the switch. Any pressure more than 9lbs may cause damage to switch.

Rack Installation

«
...
2
3
4
5
6
...
»

Содержание VT-16P250WS































Отзывы:

Нет отзывов