7
ENGLISH
Blender bowl
1. Turn the blender drive protecting cap (1)
clockwise and remove it.
2. Place the bowl (10) on the processor. Atten-
tion, the bowl (10) should be empty.
3. Turn the cap (16) anticlockwise up to the
stop.
4. Unite the marks on the bowl and the housing
of the blender (23), and turn the blender bowl
anticlockwise up to the stop.
5. Put some foodstuff into the blender bowl
(23).
6. Cover the blender bowl (23) with the cap (24)
and turn it anticlockwise to unite the marks
on the cap (24) and the handle of the blender
bowl (23).
7. Insert the power cord plug into the wall out-
let.
8. Turn the knob (3) to switch the processor on
and set the rotating speed “Max”, or turn on
pulse operating mode by pressing the button
“PULSE” (4).
9. You can add the necessary ingredients
through the opening blocked with the dis-
pensing tap (25) while the blender is operat-
ing. The dispensing tap (25) may be utilized
as the measuring glass. The maximum ca-
pacity of the tap is 60 ml.
10.
After finishing food processing switch the
appliance off by turning the knob (3) to the
“OFF” position, and disconnect the power
cord plug from the wall outlet.
11. Turn the blender bowl (23) clockwise to re-
move it.
12. Pour the mixed up foodstuff out of the blender
bowl.
Attention!
- If the cap of the bowl (16) is not installed or
installed improperly, the blender would not be
switched on.
- If the cap of the blender bowl (24) is not in-
stalled or installed improperly, the blender
would not be switched on.
- No any nozzles should be inside the blender
bowl (10) during the operation.
- Do not pour into the blender bowl (23) more
then 1000 ml of the liquid to avoid overflowing.
- Start processing the soft vegetables or fruits
(banana, for example) in the blender bowl at
the low speed, afterwards increase the speed
gradually.
- Start processing hard vegetables and fruits
(potatoes, for example) at the highest speed.
- Do not place more then 300 g of the hard veg-
etables into the blender per one session.
- The time of the blender operation should now
exceed 20-30 seconds. The break between
the consequent sessions should be at least 2
minutes.
Cleaning the processor
• After finishing the foodstuff processing and
before cleaning always turn off the appliance
and unplug the power cord from the wall out-
let.
• It is recommended to wash the detachable
components by warm water with neutral deter-
gent. Also you can use a dishwasher for clean-
ing the metal knives.
• Wipe the housing of the processor with the soft
damp cloth. Do not use a stiff sponge, abrasive
or aggressive detergent, and dissolvent also.
• Do not immense the processor housing into
the water. Do not wash the appliance under
the water jet.
• Cleaning the blender:
- Install the blender bowl into its position, and fill
it with the warm water with neutral detergent.
- Cover the blender bowl by the cap.
- Turn the blender on for about 20 seconds by
pressing the button “PULSE”. Repeat the pro-
cedure if required. Detach the blender bowl
and wash it by warm water.
Storage
• Make sure the processor is disconnected from
the wall outlet before putting it in the storage.
• Follow the instructions of the section “Clean-
ing the processor”.
• Use the compartment (2) to store the gratings,
choppers and knives for cutting potatoes for
frying.
Attention!
The cutting blades of the knives
are very sharp and dangerous, handle the
knives carefully!
• Store the appliance in the clean and dry
place.
Examples of food processing
The time of processing enlisted below is approxi-
mate. It depends on the quality of the foodstuff
and the type of the grinding (fine, normal, or
rough).
1616new.indd 7
1616new.indd 7
18.07.2008 12:19:35
18.07.2008 12:19:35
