Vitek VT-1350, Инструкция по эксплуатации

Страница: 5 / 32

ENGLISH
5
–
For lubricating the blades use only the
oil (11), supplied with the unit, or the oil
intended for similar devices.
–
Do not use vegetable oil or oil that
includes solvents. Solvents will evapo-
rate, and the remaining thick oil may slow
down the blades motion.
INSTALLING THE ATTACHMENT
–
Before installing or removing the attach-
ments (6, 7, 8, 9) switch the unit off by
setting the switch (3) to the position “0”.
–
Install the selected attachment (6, 7, 8, 9)
on the blades (1), press on the lower part
of the attachment (6, 7, 8, 9) to fix it. Make
sure that the attachment is locked on its
installation place.
–
To remove the attachment (6, 7, 8, 9) press
on the lower part and remove the attachment.
HAIR STYLING INSTRUCTIONS
•
Hair should be clean and dry during hair
cutting.
•
Before cutting hair switch the hair clipper on
by setting the switch (3) to the position «I»
and make sure that the hair clipper operates
normally and the blades move smoothly. If
there is excess oil on the blades, switch the
hair clipper off setting the power switch (3)
to the position «0» and remove the excess
oil with a dry cloth.
•
Seat a person so that his/her head is
approximately at your eye level, cover the
person’s shoulders with a towel and set hair
with the comb.
Reminder
–
Cut off a little amount of hair at a time; if
necessary you can always return to the cut
off part and trim off additional hair.
–
The best haircutting results are reached
on dry hair, not wet.
–
Comb the hair to reveal uneven locks.
–
It is better to leave longer hair after cutting
for the first time.
–
After learning your clipper better, you will
be able to arrange your hair in any style
you need.
Step one
Install the attachment (6 or 7). Switch the unit
on using the power switch (3), setting it to
the position «I». Hold the hair clipper with the
blades pointed upwards. Start cutting from the
beginning of the hair growth. Slowly move the
clipper upwards. This way cut the head back
area at the neck bottom and near the ears.
Step two
Switch the hair clipper off using the switch (3)
by setting it to the position «0» and install the
attachment (7 or 8) for cutting longer hair,
switch the hair clipper on and continue cutting
hair near the top of the head.
Step 3 – cutting in the temples area
Switch the hair clipper off, install the attachment
(6 or 7) and cut hair on the temples. Then
install the attachment (8 or 9) and continue
cutting towards the top of the head.
Step 4 – cutting the crown of the head
Using the attachment (8 or 9) cut the hair from
the top of the head towards the crown against
the hair growth direction.
•
You can cut hair against and along the direc-
tion of hair growth, but keep in mind that the
hair cut against the growth will be shorter
than the hair cut along the growth.
•
Use the attachments (6 or 7) for very short
cutting. To leave a little longer hair, use the
attachments (8 or 9).
•
To leave longer hair, take hair locks between
your fingers and cut hair using the hair
clipper.
•
You may use a comb: lift the hair locks and cut
them with the hair clipper above the comb.
•
Always start cutting from the head back.
•
Comb the hair to reveal uneven locks.
Step 5 – the final part
In the final stage of hair styling remove the
installed attachment from the clipper, turn
the blades of the clipper towards the hair and
trim hair on the temples and neck carefully.
Do not press the clipper strongly, there is
danger of injuries or cuts when open blades
come in contact with skin.
Note: during the breaks between operations
switch the hair clipper off, setting the power
switch (3) to the position «0».
•
After you finish cutting hair switch the hair
clipper off, setting the power switch (3) to
the position «0».
•
Remove the attachment and clean it off
hair, remove the blade block (1) and clean
it with the brush (10).