Vitek VT-1224 B/VT, Инструкция по эксплуатации

Страница: 6 / 73

5
ENGLISH
• Do not use the unit without a drain opening
plug installed.
• Do not use the unit after dropping in case of
visible damage or leakage.
•
Clean the unit regularly.
• Change the water softening cartridge
regularly, the cartridge service life is from 3
to 6 months, depending on water hardness
in your region.
•
In order to avoid electric shock do not open
the unit body by yourself. If unit has damages
apply to the authorized service center.
• For children safety do not leave polyethylene
bags, used as a packaging, unattended.
Attention! Do not allow children to play
with polyethylene bags and film. Danger of
suffocation!
• Do not allow children use the unit as a toy.
•
Keep the unit out of reach of children and
disabled persons. Do not allow them to use
the unit unattended.
•
This unit is not intended for usage by children
or disabled persons unless they are given
all the necessary instructions by a person
who is responsible for their safety on safety
measures and information about danger that
can be caused by improper usage of the unit.
• Keep the unit with the iron placed on the
base, away from children in a dry cool place.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
WATER SELECTION
Use tap water to fill the tank. If tap water is hard,
it is recommended to mix tap water with distilled
water in proportion 1:1, if water is too hard, mix
tap water with distilled water in proportion 1:2 or
use distilled water only.
SCALE PROTECTION SYSTEM
Removable water softening cartridge protects
unit from scale. If the water in your region is hard,
follow the recommendations given in the chapter
“WATER SELECTION”. Change the water
softening cartridge regularly (see “CLEANING
AND CARE”).
BEFORE USING THE UNIT FOR THE FIRST
TIME
Note: In case of unit transportation or storage
at low temperature it is necessary to keep it for
at least two hours at room temperature before
switching on.
– Unpack the steam station and remove all
stickers and packaging elements that can
prevent unit operation.
– Remove the protection from the soleplate
(6), if any.
–
Wipe the soleplate (6) with a soft dry cloth.
–
Make sure that the voltage of the mains
corresponds to the operating voltage of the
iron.
–
Place the unit on a flat steady heat- and
water-resistant surface, on the same level
with your ironing board.
FILLING THE WATER TANk
Note: Before removing the water tank (16) make
sure that the unit is unplugged.
1.
Remove the water tank (16) by pressing the
clamp (17) and pulling the tank (pic. 1).
2.
Pour water into the water tank (16) through
the water inlet (15) (pic. 2).
3.
Install the water tank (16) to its place until the
clamp (17) clicks (pic. 3).
Filling the water tank during operation
If the water tank (16) becomes empty during the
operation, the empty water tank indicator (10)
will flash red. You can fill the water tank during
operation without removing the tank (16).
1.
Switch off the unit by pressing the button (13)
and unplug the unit.
2.
Press the water tank (16) spout to get access
to the water inlet (15) and pour water into it
carefully (pic. 4).
3.
Lift the water tank (16) spout to close the
water inlet (15).
Notes:
–
Do not fill the water tank (16) with scented
liquids, vinegar, starch solution, descaling
reagents, chemical agents etc.
–
Do not exceed the “MAX” mark.
–
If you need to refill water during ironing,
switch off and unplug the iron.
IRONING TEMPERATURE
–
Always check the recommended iron
temperature indicated on the tag before
ironing.
–
If the tag with the ironing recommendations
is missing, but you know the type of fabric,
then use the following table to determine the
proper temperature.
VT-1224.indd 5 03.07.2012 9:13:43