background image

5

Installation  Instructions

CONTROLS AND SWITCHES

On the side of the camera is a hinged flap. The hinged flap covers various adjustment controls

and function switches.

1

1

2

2

3

3

4

4

6

7

(8)

(10)

(11a)

(12)

(13)

(9)

5

(11b)

(12)

(13)

230 VAC MODELS

COLOUR CAMERAS

MONO CAMERAS

LOW VOLTAGE MODELS

(1) Synchronisation Selection (LL/INT)

This switch is used to select the camera synchronisation mode. When the camera is connected

to an AC supply the Line-lock (

LL

) mode can be used. This locks the camera frame rate to the

mains frequency so that cameras in a system are triggered at the same point on the mains AC

cycle. Also see 5, 6 and 7 Line Lock Phase Adjustment.

(2) Backlight Compensation (BLC)

The BLC (Back Light Compensation) facility compensates for back-lit scenes by enhancing

objects in the centre of the scene which would previously have been in silhouette. Select 

ON

or 

OFF

 using the BLC switch. Default is 

OFF

. BLC will only function with a manual iris lens when

the Electronic Iris facility is switched on. For direct drive and auto iris lenses, BLC will still

function even though the Electronic Iris facility is switched off.

(3) Gamma

Two different gamma correction options are available. Select 

Normal

 (0.45) to provide increased

visibility in dark areas of the scene, or 

Linear 

(1.0). The default setting is 

Normal

.

Default switch positions shown (white represents switch position)

Содержание Protos 3 Series













Отзывы: