DE1164 CLIP-4N Installation Instructions
1
CLIP
CLIP
CLIP
CLIP----4N
4N
4N
4N
The Smallest Digital, Curtain-Type Infrared Detector
Installation Instructions
1. INTRODUCTION
1. INTRODUCTION
1. INTRODUCTION
1. INTRODUCTION
The CLIP-4N is the smallest and most elegant curtain-pattern PIR
detector, designed for adjustment-free easy installation. Its function is
based on new, patented digital signal processing.
A new technology is used to include 3 different detectors in a single
case, each programmable for optimized performance at the specific
mounting location. This results in better catch performance and
virtually no false alarms.
The superiority of this detector over similar products is achieved by
applying an improved version of the patented
True Motion
Recognition™
(TMR) algorithm. This advanced motion analysis
method allows the CLIP-4N to distinguish between the true motion of
the human body and any other disturbances that cause false alarms.
Detailed coverage patterns and mounting alternatives are given in
Figures 2 through 6 below.
Figure 1.
CLIP -4N General View
Figure
2.
Wall-Mount Curtain
Figure 3.
Ceiling-Mount Curtain
Figure 4.
Overhead Curtain
Figure 5.
Curtain / Pet Alley
Figure 6.
CLIP-4N on Internal Doorframe
2. SPECIFICATIONS
2. SPECIFICATIONS
2. SPECIFICATIONS
2. SPECIFICATIONS
OPTICAL
Number of Curtain Beams:
2
Mounting Positions:
See Figures 2 through 6.
Mounting Height:
Up to 3.6 m (12 ft).
Range:
Long, Medium and Short (jumper-selected)
ELECTRICAL
Voltage:
10 to 16 VDC.
Current Drain:
About 8 mA at 12 VDC.
Alarm Output:
Solid-state relay, N.C., up to 100 ma / 30 V, approx. 30
ohms internal resistance. Circuit opens upon alarm.
Tamper Output:
N.C., rated at 50 mA resistive / 30 VDC.
Alarm Duration:
2-3 seconds.
LED:
Walk test enabled or disabled with internal link.
Detector:
Dual-element low noise pyroelectric sensor.
Microprocessor:
8-bit, low power CMOS
.
ENVIRONMENTAL
Operating Temperature:
-10°C to 50°C (14°F to 122°F).
Storage Temperature:
-20°C to 60°C (-4°F to 140°F).
RFI Protection:
> 20 V/m to 1000 MHz.
PHYSICAL
Dimensions (H x W x D):
70 x 28 x 25 mm (2-3/4 x 1-1/4 x 1 in.).
Weight:
25 g (0.9 oz).
Color:
White.
PATENTS
U.S. Patent 5,693,943 (other patents pending)
3. INSTALLATION
3. INSTALLATION
3. INSTALLATION
3. INSTALLATION
3.1 Disassembly and Assembly
A. Removing the Front Cover
Insert a small screwdriver into
one of the narrow gaps at the
sides of the name plate (see Fig.
7). Lever carefully sideways, until
the name plate arches slightly out
and snaps free (do not let it fly
off). Retain the name plate and
loosen the screw within the inner
shaft (see Fig. 8). Remove the
cover carefully, to avoid dropping
the screw.
Figure 7.
Name-Plate Removal
B. Installing the Front Cover
Carefully fit the front cover onto
the base, with the lens in front of
the sensor, insert the screw into
its shaft and tighten it well.
Position the name plate correctly,
and insert one of the tabs into its
groove. Press the free edge
sideways against the already
seated edge, until the name plate
arches slightly outward. Then
force the other tab into its groove,
and let the name plate snap into
place.
Figure 8.
Disassembly
