Visolux OCD6000-F62-R4-V15 Скачать руководство пользователя страница 4

Страница: 4 / 20

Static scanner OCD6000-F62-...

General safety Instructions

e of

iti

on:

Subject to reasonable modifications due to technical advances.

Fuchs Group • Tel.: G49 621 776-0 • USA +1 330 4253555 • Sin65 67799091 • Internet http://www.pepperl-fuchs.com

General safety Instructions

Observe all state and national safety and accident prevention require-
ments and the following safety instructions in these operating instruc-
tions when performing any tasks on the OCD6000-F62.

Before the OCD6000-F62 is placed in service, this instruction manual
must be read carefully.

Maintenance and mounting tasks must only be performed when there
is no electrical power flowing in the device.

Any other function than what is described in this manual is contrary to
the intended purpose and must therefore be excluded.

If malfunctions cannot be eliminated, the device must be taken out of
operation and protected from being inadvertently placed back in opera-
tion.

Repairs may only be performed by the manufacturer. Intervention into
and modifications of the device are not permissible.

Other important safety guidelines may be found in the individual sec-
tions of this construction manual.

Warning

Caution

Note

Содержание OCD6000-F62-R4-V15





















Результаты поиска

Содержание OCD6000-F62-R4-V15

Отзывы:

Бренды по названию

Популярные бренды

Visolux OCD6000-F62-R4-V15, Инструкция по эксплуатации

Результаты поиска

Содержание OCD6000-F62-R4-V15

Отзывы:

Бренды по названию

Популярные бренды