Viso Systems LabSpion Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 42

background image

15

LabSpion user guide

Connecting lamp power

The LabSpion has a build in power analyser and power
switch. The power switch is used to switch of the lamp
before a measurement is made so the ambient light can be
measured and subtracted from the subsequent
measurement.

The maximum
supported lamp
current is 3A which
is 660W at 220VAC
and 330 at 110VAC.

AC power supply cable plug

Warning: Risk of electric shock! Plug
installation shall be performed by a qualified
electrician.

A grounding-type (earthed) power plug that fits the local
power outlet must be used which you can acquire an IEC
power cable with a suitable grounding-type plug from most
consumer electronics stores.

When installing the plug connect pins as follows:

yellow and green wire to ground (earth)

blue wire to neutral

brown wire to live

«
...
13
14
15
16
17
...
»

Содержание LabSpion











































Отзывы:

Нет отзывов

Похожие инструкции для LabSpion

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: York Fitness Страницы: 36

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

Бренд: Yacht Devices Страницы: 68

TUV COMFORT LIGHT Series

Бренд: olympia electronics Страницы: 4

Бренд: Bavis Страницы: 8

Бренд: Gomaco Страницы: 30

Бренд: Panduit Страницы: 4

BIO-FIGHTER 4Xtreme

Бренд: Dust Free Страницы: 8

Бренд: HF Scientific Страницы: 5

Бренд: Lightolier Страницы: 2

Бренд: Mueller Страницы: 2

Tractelift Type II

Бренд: Tractel Страницы: 28

Бренд: WENVY Страницы: 23

SnapTable PRO Hyper-Lite

Бренд: SWENSON SHEAR Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды