Visive Hi-Lite 30 Border Скачать руководство пользователя страница 5

Page 3 

Hi-Lite™ 30 LED contour tube specification & installation 

v6 – June 2021

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

50-70mm

(2”-2¾”)

50-70mm

(2”-2¾”)

The installation

 (continued)

1. 

Mounting clips must be installed 

along a perfectly straight line. Clips installed 
off-centre will pull the Hi-Lite™ 30 section out of alignment.  
Snap a chalk line on the mounting surface to use as a guide. Position  
a clip 50-70mm (2”-2¾”) from the end of each Hi-Lite™ 30 section and at least every 
400mm (1’3¾”) along each length.

2

On horizontal installs, clips must be 

installed with the spring part of the clip to 
the bottom edge. The groove along the rear 
of the clip indicates the centre line of the 
Hi-Lite™ 30 tube once installed. Use fixings 
with head diameter between 7mm (0.3”)  
and 9mm (0.35”).

3. 

Two types of clip are supplied. A high-

friction clip should be used in the centre of 
the section. This clip features a rubber ‘O’ 
ring to increase the grip on the tube, thereby 
locking it in position. Only one high-friction 
clip must be used per section.

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

50-70mm

(2”-2¾”)

50-70mm

(2”-2¾”)

This way up

Chalk centre line

Fixing screw / rivet

Head diameter: min 7mm (0.3”), max 9mm (0.35”)

Standard clip

4. 

On vertical installations, the high-friction 

clip is particularly important to prevent 
Hi-Lite™ 30 sections from slipping down 
over time.

5. 

If a standard section is to connect to further 

sections loop the output connection as shown 
before fitting the tube into position. Leave a 
loop of cable to allow for movement due to 
thermal expansion and contraction.

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

<400m

m

(1’3¾”)

50-70mm

(2”-2¾”)

50-70mm

(2”-2¾”)

Loop of wire to 

allow for thermal 

movement

High-friction clip

‘O’ ring

Visive Group Limited
Ash Road South, Wrexham Industrial Estate, Wrexham, LL13 9UG   +44 (0) 1978 660181

 

www.visivegroup.com

Содержание Hi-Lite 30 Border













Отзывы: