background image

 

Regulatory Information 

 

FCC Information 

 

FCC compliance: 

This equipment has been tested and found to comply with the limits for a digital 

device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable 
protection against harmful interference when the equipment is operated in a commercial environment. 
This  equipment  generates,  uses,  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and 
used  in  accordance  with  the  instruction  manual,  may  cause  harmful  interference  to  radio 
communications.  Operation  of  this  equipment  in  a  residential  area  is  likely  to  cause  harmful 
interference in which case the user will be required to correct the interference at his own expense. 
 

FCC Conditions

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: 
1. This device may not cause harmful interference. 
2. This device must accept any interference received, including interference that may cause 
undesired operation. 

EU Conformity Statement

 

This product and -if applicable -the supplied accessories too are marked with 
"CE" and comply therefore with the applicable harmonized European standards 
listed under the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU. 
 
2012/19/EU (WEEE directive): Products marked with this symbol cannot be 
disposed of as unsorted municipal waste in the European Union. For proper 
recycling, return this product to your local supplier upon the purchase of 
equivalent new equipment, or dispose of it at designated collection points. For 
more information see: www.recyclethis.info. 
 
 
2006/66/EC (battery directive): This product contains a battery that cannot be 
disposed of as unsorted municipal waste in the European Union. See the 
product documentation for specific battery information. The battery is marked 
with this symbol, which may include lettering to indicate cadmium (Cd), lead 
(Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or 
to a designated collection point. For more information see: www.recyclethis.info. 
 
 

Industry Canada ICES-003 Compliance

 

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. 

 

 

 

 

 

 

 

 

Содержание VS-AXESS-2ETL
























Отзывы: