background image

 
                                                                                     

 

2-

  1. Safety Instruction   

     

 

WARNING 

 

y

  Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that 

they also receive this instruction booklet. 

 

Caution

 

y

  All fixtures are intact from the manufacturer, please operate follow up the user manual, artificial fault 

are not under guarantee repair. 

y

  Unpack and check carefully there is no transportation damage before using the unit

 

y

  The unit is for indoor use only. Use only in a dry location

 

y

  Do install and operate by operator

 

y

  Use safety chain when fixes the unit

 

y

  The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent 

surfaces.  

y

  Be sure that no ventilation slots are blocked, otherwise the unit will be overheated. 

y

  Before operating, ensure that the voltage and frequency of power supply match the power 

requirements of the unit. 

y

  It’s important to ground the yellow/green conductor to earth in order to avoid electric shock. 

y

  Maximum ambient temperature TA : 40

. Don’t operate it where the temperature is higher than this.

 

y

  Don’t connect the device to any dimmer pack. 

y

  First run, there will be smoke or smells, and all disappearing a few minutes later. 

y

  Make sure there are no flammable materials close to the unit while operating, as it is fire hazard. 

y

  Look over power wires carefully, replace immediately if there is any damage. 

y

  Unit surface temperature may reach up to 60

. Don’t touch the housing bare

-hand during its 

operation. 

y

  Never run on for a long time lest shortening lifespan. 

y

  Avoid any inflammable liquids, water or metal objects entering the unit. Once it happen, cut off the 

mains power immediately. 

y

  Do not operate in dirty and dusty environment, also cleaning fixtures regularly. 

y

  Do not allow children to operate the fixture. 

y

  Do not touch any wire during operation as there might be a hazard of electric shock. 

y

  Avoid power wires together arounding other cables. 

y

  Replace fuse only with the same type. 

y

  In the event of serious operating problem, stop using the unit immediately. 

y

  Never turn on and off the unit time after time. 

Please read the instructions carefully which includes important 

information about the installation, operation and maintenance. 

Содержание VG-4-3TC-P











Отзывы: