Vishay TSOP573 Series Скачать руководство пользователя страница 9

TSOP573.., TSOP575..

www.vishay.com

Vishay Semiconductors

 

 

Rev. 1.4, 25-Feb-14

9

Document Number: 82450

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 

www.vishay.com/doc?91000

LABEL

Standard bar code labels for finished goods

The standard bar code labels are product labels and used 
for identification of goods. The finished goods are packed in 
final packing area. The standard packing units are labeled 

with standard bar code labels before transported as finished 
goods to warehouses. The labels are on each packing unit 
and contain Vishay Semiconductor GmbH specific data.

DRY PACKING

The reel is packed in an anti-humidity bag to protect the 
devices from absorbing moisture during transportation and 
storage.

FINAL PACKING

The sealed reel is packed into a cardboard box. A secondary 
cardboard box is used for shipping purposes.

 

 

 

RECOMMENDED METHOD OF STORAGE

Dry box storage is recommended as soon as the aluminum 
bag has been opened to prevent moisture absorption. The 
following conditions should be observed, if dry boxes are 
not available:

• Storage temperature 10 °C to 30 °C

• Storage humidity 

 60 % RH max.

After more than 168 h under these conditions moisture 
content will be too high for reflow soldering.

In case of moisture absorption, the devices will recover to 
the former condition by drying under the following condition:

192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air/nitrogen) 
or 

 

96 h at 60 °C + 5 °C and < 5 % RH for all device containers 
or 

 

24 h at 125 °C + 5 °C not suitable for reel or tubes.

An EIA JEDEC

®

 standard J-STD-020 level 3 label is included 

on all dry bags.

VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL

 (Finished goods)

PLAIN WRITING

ABBREVIATION

LENGTH

Item-description

-

18

Item-n

u

m

b

er

INO

8

Selection-code

SEL

3

LOT-/serial-n

u

m

b

er

BATCH

10

Data-code

COD

3 (YWW)

Plant-code

PTC

2

Q

u

antity

QTY

8

Accepted 

b

y

ACC

-

Packed 

b

y

PCK

-

Mixed code indicator

MIXED CODE

-

Origin

Company logo

Long bar code top

Type

Length

Item-n

u

m

b

er

N

8

Plant-code

N

2

Se

qu

ence-n

u

m

b

er

X

3

Q

u

antity

N

8

Total length

-

21

Short bar code bottom

Type

Length

Selection-code

X

3

Data-code

N

3

Batch-n

u

m

b

er

X

10

Filter

-

1

Total length

-

17

Aluminum bag

Label

Reel

15973

Содержание TSOP573 Series












Отзывы: