background image

 

                                                                                                  LED-HC 101 

 

                                                                                                                               

     

4-

 

5. DIP SWITCH: used to set the start address of the unit or choose functions   

6. AUTO DMX ADDRESS: used to set start address automatically. 

7. LED-WD CONNECTOR: used to receive the signal of LED-WD only 

8. SIGNAL OUTPUT: output signal and power for light   

 

 

4. Installation 

 

 

1. Ensure that mains power supply is off before installing or wiring the LED fixture 

2. Unscrew the screws and connect the wires as diagrams below 

3. Tight the screws. 

 

     

 

 

CAUTIONS

the LED controller total output power consumption is 100 watt.   

 

5. DMX512 Address Setting   

Each  fixture  needs  to  have  a  start  address  set  to  receive  the  data  sent  by  the 

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). The 

address,  also  know  as  the  start  channel,  is  the  first  channel  used  to  receive 

instructions from the controller. 

 

There are four ways to set the fixture DMX start address:   

A.  DMX address setting by dip-switches   

B.  Auto DMX addressing   

Содержание LED HANDY CON 101














Отзывы: