virtual access GW9000 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 14

virtual access GW9000 Series Скачать руководство пользователя страница 7

Error! Reference source not found.: Error! Reference source not found.

______________________________________________________________________________________________________

Connect the RJ11 end of the purple cable to the port marked DIAL MODEM.
Connect the other end to the ADSL socket on the wall or to the splitter. This
socket can be an RJ45 or an RJ11 port. The RJ11 connector will fit into both.
To connect directly to an ADSL service, connect one end of the RJ11 connector
on a purple cable to the port marked ADSL-0. Connect the other end of the RJ11
connector to the ADSL socket on the wall. This socket can be an RJ45 or an RJ11
port. The RJ11 connector will fit into both.
If you are using a cable modem or ADSL modem and not a direct service
connection, do not connect the ADSL cable. Connect on end of the Ethernet
cable to the appropriate Ethernet port on the router. Connect the other end to
the Ethernet port on your cable modem or ADSL modem.
Connect the power supply connector to the power port on the back of the router.
The config LED on the front of the router will flash if it is in factory config mode.
If the router is pre-configured the config LED will be solid.

3.5

Connecting a GW9000 router with a serial connection

Figure 3: Serial and power connections on the rear of a GW9000 series router

If you are using a serial connection, connect the serial cable to the serial port on
the back of the router.
Connect the power supply to the power port on the back of the router.
The config LED on the front of the router will flash if it is in factory config mode.
If the router is pre-configured the config LED will be solid.
If your serial connection is configured and connected to the network correctly,
the serial SYNC LED will be lit and solid. If data is transmitting correctly across
the serial link, the data LED will blink intermittently. If the LEDs on your router

______________________________________________________________________________________________________

© Virtual Access 2014

Installing a GW9000 Series Router

Issue 2.0

Page 7 of 14

«
...
5
6
7
8
9
...
»

Содержание GW9000 Series















Отзывы:

Нет отзывов