Viqua S2Q-PV Скачать руководство пользователя страница 10

Specifications

10

4.3 Alarm Connection

An Alarm feature is provided in the vending ballast allowing for dry contact connection for indicating when the system goes 

into a lamp OFF alarm condition and the UV unit is no longer disinfecting the water source. The Alarm contacts are 

controlled by an internal relay within the ballast. When the unit is functioning and the lamp is ON the C to NO connection is 

closed and the C to NC connection is open. When the UV lamp turns off the ballast senses this alarm condition and causes 

the relay to shut off. This now causes the C to NO connection to open circuit and the C to NC to close. These connections 

can be configured in any manner appropriate for your application.

1.

To connect to these contacts pull to remove the detachable terminal connecting plug from the Alarm side of the ballast.

2.

Connect the appropriate wire configuration required as identified on the connector label. C is the common point; NC is 

open and NO is closed when the system is operating properly.

Note: 

Contact Rating Maximum of 2.0 amps @ 240VAC

3.

Once the connections are made secure the wires with the terminal screws and plug the connector back onto the ballast 

Alarm side.

Section 5

Specifications

C A U T I O N

Ensure Alarm connector is connected to the Alarm side of the Ballast.

Model

S2Q-PV

S5Q-PV

S5Q-PV-ASPL

Flow R

ate

1

US Public Health 16mJ/cm

2

5 gpm (19 lpm) (0.9 m

3

/hr)

11 gpm (42 lpm) (2.5 m

3

/hr)

11 gpm (42 lpm) (2.5 m

3

/hr)

Standard 30 mJ/cm

2

3 gpm (11 lpm) (0.7 m

3

/hr)

6 gpm (23 lpm) (1.4 m

3

/hr)

6 gpm (23 lpm) (1.4 m

3

/hr)

NSF/EPA 40 mJ/cm

2

2 gpm (7 lpm) (0.5 m

3

/hr)

4.5 gpm (17 lpm) (1.0 m

3

/hr)

4.5 gpm (17 lpm) (1.0 m

3

/hr)

D

imensions

Length

47 cm (18.5”)

56 cm (22”)

56 cm (22”)

Width

6.5 cm (2.5”)

6.5 cm (2.5”)

6.5 cm (2.5”)

Height

6.5 cm (2.5”)

6.5 cm (2.5”)

6.5 cm (2.5”)

Diameter

6.5 cm (2.5”)

6.5 cm (2.5”)

6.5 cm (2.5”)

Shipping Weight

2.7 kg (6 lbs)

2.7 kg (6 lbs)

2.7 kg (6 lbs)

Electr

ical

Voltage

100-250 V / 50/60 Hz

100-250 V / 50/60 Hz

100-250 V / 50/60 Hz

Max. Current 

0.6 Amp

0.6 Amp

0.6 Amp

Power Consumption

19 W

26 W

26 W

Lamp Watts

17 W

22 W

22 W

Maximum Operating Pressure

125 psi (861 kPa)

125 psi (861 kPa)

125 psi (861 kPa)

Minimum Operating Pressure

15 psi (103 kPa)

15 psi (103 kPa)

15 psi (103 kPa)

Ambient Water Temperature

2-40 ºC (36-104 ºF)

2-40 ºC (36-104 ºF)

2-40 ºC (36-104 ºF)

Inlet/Outlet Port Size

1/2” MNPT

3/4” MNPT

3/8” NPTF

Visual “Power-On”

Yes

Yes

Yes

Chamber Material

304 SS

304 SS

304 SS

Units ending in "/MEX" meet the requirements established in the Mexican Official Norm NOM-244-SSA1-2008

Содержание S2Q-PV













Отзывы: