background image

PROPRIETARY NOTICE

ViPowER Inc. makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. ViPowER Inc. shall not be liable for errors
contained herein or for incidental or consequential damages in connection
with the furnishing, performance, or use of this material.

This document contains proprietary information which is protected by copy-
right. All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the written consent of
ViPowER Inc. The information contained in this document is subject to
change without notice.

1-1 Introduction ........................................................................... 1

1-1.1 CD-ROM Box Enclosure Features .............................. 1
1-1.2 ATA/ATAPI Device Compatibility ................................. 1
1-1.3 Unpacking Your CD-ROM Box .................................... 1

2-1 Installation ............................................................................ 2

2-1.1 Disassemble the CD-ROM Box ................................... 2
2-1.2 Assemble CD-ROM Box with CD-ROM Drive .............. 3

3-1 Operation with a Docking Kit ................................................. 5

3-1.1 Disconnecting the CD-ROM Box ................................. 6

Table of Contents

PC is a trademark of International Business Machines Corporation.
Windows is a registered trademark of Microsoft Corporation.
All other trademarks belong to their respective owners.

© Copyright 2000 by ViPowER, Inc.

3/00A

Содержание CD-ROM Box Enclosure VP-6020









Отзывы: