VIPA SLIO 001-1BA00 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 48

VIPA SLIO 001-1BA00 Скачать руководство пользователя страница 39

Manual VIPA System SLIO

Chapter 2 Power modules

HB300E - PS-CM - Rev. 11/28

2-9

The following figure shows the standard cabling of the power supply by
means of a bus coupler.

DC24V

0V

DC24V

0V

1

2

DC24V max. 10A

SysDC5V max. 3A

(1) DC 24V for power section supply I/O area
(2) DC 24V for electronic power supply bus coupler and I/O area

With a sum current greater than 3A the LEDs may not be activated. When
the power module 007-1AB10 is placed, further modules may be placed
besides the power module at the backplane bus, whose sum current of
electronic power supply does not exceed 2A. On this way the System SLIO
may be expanded up to a maximum of 64 modules.
Additionally the power module serves for a new isolated group for the DC
24V power section supply with max. 4A.

007-1AB10

Sys DC 5V: 2A

DC 24V: 4A

007-1AB10

Sys DC 5V: 2A

DC 24V: 4A

DC24V

0V

DC24V

0V

DC24V max. 10A

SysDC5V max. 3A

SysDC5V max. 2A

SysDC5V max. 2A

DC24V max. 4A

DC24V max. 4A

DC24V

0V

DC24V

0V

1

2

3

3

DC24V

0V

4

DC24V

0V

4

(1) DC 24V for power section supply I/O area (max. 10A)
(2) DC 24V for electronic power supply bus coupler and I/O area
(3) DC 24V for power section supply I/O area (max. 4A)
(4) DC 24V for electronic power supply I/O area

Standard wiring

Expansion by the
power module
007-1AB10

«
...
37
38
39
40
41
...
»

Содержание SLIO 001-1BA00

















































Отзывы:

Нет отзывов