manualshive.com logo in svg

Vintage Model Co JODEL D-18, Инструкция пользователя, Страница: 15 / 36

Поделиться
Скачать
Vintage Model Co JODEL D-18 Скачать руководство пользователя страница 15

15

Jodel D-18

THE FIN AND RUDDER

1)   Identify and remove all of the parts on the laser 

cut sheets: 

FR1-FR6 and 1 off corner gusset

.

2)   From the 1.6mm square strip cut all of the ribs using 

the plan to get the right length. Set these aside. 

3)   Pin down the fin and rudder trailing and leading 

edges FR1 and FR3.

4)   Offer up parts FR2, FR4, FR5, and the rib which 

meets the fuselage. When you are happy, glue in 

position with snug butt joints. Allow this outline to set.

5)   Once the outline is set, glue all of the ribs in 

place adjusting the length if necessary. Glue 

FR6 and the corner gusset in position. 

6)   Leave to set then remove from the board and 

give both sides as well as the outside edges 

a light sand. Be careful so as not to make the 

structure too thin or cause unevenness in the 

surface by over sanding.

VMC Instruction Booklet - Jodel JAN19.indd   15

19/01/2019   12:06

Содержание JODEL D-18





































Отзывы:

Нет отзывов