manualshive.com logo in svg

Vintage Model Co JODEL D-18, Инструкция пользователя, Страница: 14 / 36

Поделиться
Скачать
Vintage Model Co JODEL D-18 Скачать руководство пользователя страница 14

14

vintage

model

company

.com

THE TAIL PLANE (STABILIZER)

For the tail plane, and fin/rudder use the shorter 

lengths of 1.6mm square strip from the lighter sheet 3.
1)   Identify and remove all of the parts on the laser 

cut sheets: 

T2, T4 and T5 (2 off each) T1, T3 

and 12 off corner gussets

.

2)   From the 1.6mm square strip, cut all of the ribs using 

the plan to get the right length. Set these aside. 

3)   Pin down the tail plane central spar T1 and the 

leading edge T3.

4)   Trial fit the parts T2 making any small 

adjustments to the positions of T1 and T3 to 

make a snug fit. When you are satisfied, glue 

both T2 parts in position making sure that you 

have nice neat butt joints.

 5)  Trial fit parts T4 and T5 each side. Once you are 

satisfied they are a good fit, glue into position. 

Allow this outline to set.

6)   Once the outline is set, glue all of the ribs in 

place adjusting the length if necessary. Glue the 

12 off corner gussets in position.

7)   Leave to set then remove from the board and 

give both sides as well as the outside edges 

a light sand. Be careful so as not make the 

structure too thin or cause unevenness in the 

surface by over sanding. 

VMC Instruction Booklet - Jodel JAN19.indd   14

19/01/2019   12:06

Содержание JODEL D-18





































Отзывы:

Нет отзывов