manualshive.com logo in svg

Vintage Model Co 702785155561, Руководство пользователя

Поделиться
Скачать
Vintage Model Co 702785155561 Скачать руководство пользователя страница 31

31

Sopwith F1 ‘Camel’

TRIMMING AND FLYING YOUR MODEL

When flying your model, choose a large area 

free from any obstructions. Do not fly it towards 

people or property.

To fly successfully, your model must be correctly 

trimmed. Trimming is a normal procedure for any 

aircraft, but for a free flight model it is especially 

significant as once the model is released, you have 

no control over it. Trimming takes some time and 

skill and the basics are outlined here. More detailed 

information and help is available from the many 

experienced free flight modellers who have websites 

dedicated to the subject or post information on 

numerous on-line forums.

The first step involves fitting the motor and 

checking the balance. Short test flights should then 

be carried out during which the behaviour of the 

model can be observed. Following initial flight tests, 

the number of winds on the motor and thus the 

duration of the flights can be slowly increased.

VMC Instruction Booklet - Sopwith Camel JAN19.indd   31

19/01/2019   12:16

Содержание 702785155561









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды