Vimar 01546 Скачать руководство пользователя

Страница: 11 / 21

VIMAR group

ETS parameters and communication objects

COMMUNICA

TION OBJECTS

KNX weather station

Reference ETS parameters

Behaviour in the event of a power failure and when

power is restored.

Behaviour if there is no Bus voltage or auxiliary voltage:

The device transmits no data.

Behaviour if there is no Bus voltage or auxiliary voltage and
subsequent programming or restarting:

The device sends all the measured values, control outputs and
the status of the logic gates according to the behaviour set by
the parameters in the "General Settings". When powering up,
information will be sent with a settable delay.

General settings

ETS text

Available values

Comment

[

Default value

]

Send measured values

periodically all

5 s ... 2 h

[5 s]

Send control outputs peri-

odically all

5 s ... 2 h

[5 s]

Send logic outputs

periodically all

5 s ... 2 h

[5 s]

Logic input communication

objects

do not enable
enable

[do not enable]

Night control output com-

munication object

Do not send

Send with change

Send reversed with

change

Send with change and

cyclically

Send reversed with

change and cyclically

[Send with change]

Rain control output com-

munication object

Do not send

Send with change

Send reversed with

change

Send with change and

cyclically

Send reversed with

change and cyclically

[Send with change]

Control output transmission

delay after Power up and

programm.

5 s ... 2 h

When powering up

and after program-

ming, the weather

station waits for the

set time delay before

transmitting the

control outputs.

[10 s]

Maximum speed of the

1... 20 telegrams

per second

[5 telegrams per

second]

Содержание 01546






















Результаты поиска

Содержание 01546

Отзывы:

Похожие инструкции для 01546

Бренды по названию

Популярные бренды

Vimar 01546, Руководство по установке

Результаты поиска

Содержание 01546

Отзывы:

Похожие инструкции для 01546

Бренды по названию

Популярные бренды