INSTALLATION
ELECTRICAL CONNECTION
The installation, connection and any repairs that may be necessary should only be carried out by a qualified installer.
There is a zone lay-out for bathroom areas. These must be respected.
The Netherlands:
in accordance with NEN 1010
Belgium:
in accordance with A.R.E.I.; art. 86, 90, 93
Germany:
in accordance with DIN/VDE 0100 Teil 701; 2002-02
France:
in accordance with NF C 15-100
UK:
in accordance with BS 7671
Other countries:
in accordance with local connection regulations applying.
The system meets the requirements set for Class 1 equipment. The system must be permanently connected to a fixed wiring system, on a
separate final group, with a cable of at least 3 x 2.5 mm2 (type H05VV-U3G2.5 or H05VV-F3G2.5) and protected with a 16 Ampère fuse.
Type X attachment with special prepared cord — If the supply cord is damaged, you must replace it by a special cord or assembly available
from the manufacturer or a service agent.
In the power supply, a cut-off switch should be installed which:
- is situated under the seat area or behind the cabin A close to the control unit.
- must switch both the phase and the zero.
- must have a contact opening greater than 3 mm in the switched-off position.
- complies with safety requirements of IPX5.
A connection for an equipotential bonding is provided on the frame of the system. This must be connected in accordance with local regulations
to the equipotential bonding line which should be present in the bathroom.
A Residual Current Circuit Breaker must be incorporated into the power line (I
∆
max = 30 mA, In = 25 A).
All electrical equipment, such as the cut-off switch, wiring and similar must be fitted at least 20 mm above floor level.
Repairs to electrical equipment may only be carried out by a qualified person.
CONNECTION TO THE WATER MAINS
- Before connection, two angled stop taps should be mounted into the wall. Before the flexible hoses for hot and cold water are connected,
the supply pipes should be flushed thoroughly to prevent any debris (grit, plaster etc.) getting into the system.
- Check valves are incorporated in the supply hoses.
The manufacturer is not responsible for the consequences of incorrect installation.
CHECK
Although your system has been thoroughly checked in the factory, damage could have been caused during transport or when installing.
Therefore the following procedure must be followed after installation and before tiling etc. For that reason, the following procedure should be
applied after installation.
- Switch on the power supply.
- Next, check that the system is working properly (refer to the INSTRUCTIONS FOR USE section for this).
- Check for leaks.
- Wait for 10 minutes, then check again for leaks.
GUARANTEE
This quality product comes with the following guarantee:
- Cabin (shower tray, dome, glass): 3 years
- Fittings: 1 year
- Technical parts: 1 year
The guarantee covers: factory faults, changes in colour and/or cracks resulting from material ageing, and distortion caused by hot water. The
guarantee is limited to the repair or replacement of products and does not cover glass parts if the glass should break. The guarantee is only
valid if the product was installed in accordance with our installation/maintenance terms and conditions. It must not be provided with a system
developed or fitted by third parties and must not be subjected to modifications which are not indicated in the installation provisions
accompanying the product, with the exception of the drilling of holes, at the places indicated, for the building-in of loudspeakers into the Steam
Cube dome. To claim against the guarantee please contact your local dealer. Consequential damages and the cost of building-in or removing
elements are not covered by the guarantee.
Technical Information
Technical Information
1. ELECTRICAL SYSTEM
- Degree of protection IP24.
- Class I.
- Power supply 230 V, 50 Hz, fuse 16 A.
- Total absorbed power 3000 Watt.
2. STEAM GENERATOR
- 230 Volt, 50 Hz, 2800 Watt.
.
3. LIGHTING
- 230 V, 50 Hz, MAX 10W.
- Class II.
4.WATER SUPPLY REQUIREMENTS
- Minimum pressure at connection point: 2 bar
- Maximum pressure at connection point: 5 bar
- Maximum hot/cold pressure variation: 30%.
- Minimum diameter of cold and hot supply pipes: 15 mm.
- Minimum flow from hot water point: 8 l/min.
- For optimum simultaneous functioning of several water applications, a pipe diameter of 22 mm
and a hot water flow rate of 14 l/min. is recommended.
CE MARK
- The entire system meets the current European EMC and low-tension directives.
GB
29
Содержание PRO
