manualshive.com logo in svg

Viking Quiet Cool VCRB5301, Руководство по обслуживанию, Страница: 28 / 47

Поделиться
Скачать
Viking Quiet Cool VCRB5301 Скачать руководство пользователя страница 28

Service Procedures

28

©2012 Viking Preferred Service

FAST

COOL

LOWER

HIGHER

ALARM

OFF

HIGHER

LOWER

FAST

COOL

HIGHER

LOWER

LOWER

HIGHER

MAX

REF

While in Mode B, press and 

release "FAST COOL" one time, 

this will result in "FAST COOL" 

illuminating on the display along 

with the current numeric value in 

hours that FAST COOL is set at. 

Factory default for this adjustment 

is 2 hours. Range is 1 to 20 hours 

in 1 hour increments.

The duration is adjusted using the "HIGHER 

and LOWER" pads.

While in Mode B, press and release "ALARM 

OFF" one time, this will result in "DOOR 

While in Mode B, press and 

release "FAST COOL" one time, 

this will result in "FAST COOL" 

illuminating on the display along 

with the current numeric value in hours that 

FAST COOL is set at. Factory 

default for this adjustment is 2 

hours. Range is 1 to 20 hours in 1 

hour increments.

The duration is adjusted using the 

"HIGHER and LOWER" pads.

Adjust FAST COOL duration

Adjust Door Open Alarm delay

Adjust Compressor Dwell Time

This adjustment is not a field adjustment and 

should not be performed by technicians. This 

is a factory only adjustment. If you see "Cdt" 

in the display, immediately exit Mode B by 

holding "ACTIVATE CONTROLS" for three 

seconds until you get three audible beeps. 

Return to your previous actions.

Adjust FAST COOL duration

While in Mode B, press and release "MAX 

REF" one time, this will result in "MAX REF" 

illuminating on the display along 

with the current numeric value in 

hours that MAX REF  is set at. 

Factory default for this adjustment 

is 4 hours. Range is 1 to 20 hours 

in 1 hour increments.

The duration is adjusted using the 

"HIGHER and LOWER" pads.

Adjust MAX REF duration

OPEN" illuminating on the display 

along with the current numeric 

value in minutes that the delay 

is set at. Factory default for this 

adjustment is 3 minutes. Range 

is 1 to 20 minutes in 1 minute 

increments.

The duration is adjusted using the 

"HIGHER and LOWER" pads.

Содержание Quiet Cool VCRB5301
















































Отзывы:

Нет отзывов