manualshive.com logo in svg

Viking Quiet Cool VCRB5301, Руководство по обслуживанию, Страница: 10 / 47

Поделиться
Скачать
Viking Quiet Cool VCRB5301 Скачать руководство пользователя страница 10

Operation

Description

How to Access Function

Keyboard Entry Tone

Indicates a pad was pressed, com-

mand was read, and accepted

To turn off entry tone, press and hold 

“ACTIVATE CONTROLS” pad for 3 

to 5 seconds

Command Accepted  Tone

Three short tones sound indicating a 

command has been accepted

"ACTIVATE CONTROLS" Pad

If the pad is activated, the display 

panel remains active at least 10 

minutes after the door is closed

Press the “ACTIVATE CONTROLS” 

pad

"REF" TEMP" Pad

"REFRIGERATOR" will light up and 

buffered freezer temperature will be 

displayed. Factory setting is 38

o

 F

Press “HIGHER” or “LOWER” pad

"HIGHER" Pad

Raises temperature settings one 

degree at a time

Press “HIGHER” pad. To raise 

temperature at a faster rate, hold the 

pad down

"LOWER" Pad

Lowers temperature settings one 

degree  at a time

Press “LOWER” pad. To lower 

temperature at a faster rate hold, the 

pad down

"FAST COOL" Pad

"FAST COOL" will light up enabling 

the fast cool function which changes 

the freezer set point to max frz and 

the ref set point to max ref for a fac-

tory default of 2 hours.

Press "FAST COOL" pad. A second 

press will disengage feature.

"MAX REF" Pad

Sets refrigerator temperature to 

coldest setting (33

o

 F). Factory set-

ting is 4 hours

Press “MAX REF” Pad to engage. A 

second press will disengage feature

"ALARM OFF" Pad

Deactivates (partially or fully), audio/

visual alarm signals 

Press “ALARM OFF” to terminate 

audible alarm, visual alarm indica-

tors will continue to blink until alarm 

condition is cleared or permanently 

disabled. To reactivate press and 

hold “ALARM OFF” pad for 3 sec-

onds.

"DISPLAY OFF" Pad

Deactivates control panel except for 

"ACTIVATE CONTROLS" and "DIS-

PLAY OFF" pads

Press “DISPLAY OFF” pad to de-

activate display. Press “ACTIVATE 

CONTROLS” pad to reactivate

Operation

10

©2012 Viking Preferred Service

Display Panel Operation

The unit being serviced has a control panel that allows operation of the unit as well as diagnostic abilities. 

See the information below for details.

Содержание Quiet Cool VCRB5301
















































Отзывы:

Нет отзывов