Viking Professional VGRT4214QSS, Инструкция по использованию и уходу

Страница: 8 / 12

15
Burner Caps
The surface burner caps should be routinely removed and cleaned.
Always clean the burner caps after a spill over. Keeping the burner caps
clean will prevent improper ignition and uneven flames. To clean, pull
burner cap straight up from the burner base. Wipe off surface burner
caps with warm, soapy water and a soft cloth after each use. Use a a non-
abrasive cleanser such as Bon Ami
TM
and a soft brush or soft Scotch
Brite TM pad for cooked-on foods. Dry thoroughly after cleaning. For best
cleaning and to avoid possible rusting, do not clean in dishwasher or
self-cleaning oven. When replacing burner caps, carefully align the tabs
underneath the cap with the outside edge of burner. Make sure burner
cap is level.
14
Cleaning and Maintenance
Kitchen Equivalents and Metrics
Measure Equivalent Metric*
1 tablespoon 3 teaspoons 15 mL
2 tablespoons 1 ounce 30 mL
1 jigger 1 1/2 ounces 45 mL
1/4 cup 4 tablespoons 60 mL
1/3 cup 5 tbsp. plus 1 tsp. 80 mL
1/2 cup 8 tablespoons 125 mL
1 cup 16 tablespoons 250 mL
1 pint 2 cups 30 grams
1 pound 16 ounces 450 grams
2.21 pounds 35.3 ounces 1 kilogram
*Rounded for easier measuring
Any piece of equipment works better and lasts longer when maintained
properly and kept clean. Cooking equipment is no exception. Your
rangetop must be kept clean and maintained properly.
Make sure all burners are “off” before cleaning. Disconnect power if you
are going to clean thoroughly with water.
Open Surface Burners (If applicable)
Wipe up spill-overs as soon as possible after they occur and before
they get a chance to burn in and cook solid. In the event of a spill-
over, follow these steps:
1. Allow the burner and grate to cool to a safe temperature level.
2. Lift off the burner grates.
3. If the spill is contained in the bowl of the grate support, just remove
the bowl and clean in warm soapy water.
4. Lift the grate support off.
5. Wash these parts in hot, soapy water and rinse clean.
6. If the spill has gone lower than the grate supports, draw out the
drip pan and wash with hot, soapy water.
If ports on the burners are clogged, clean with a straight pin. Do not
enlarge or disort the ports. Do not use a toothpick to clean the ports.
Make sure burner cap is level. Occasionally check the burner for proper
size and shape. If flames lift off ports, are yellow, or are noisy when
turned on, you may need to clean the burners or call a qualified
technician for adjustments.
Sealed Surface Burners (If applicable)
Wipe up spill-overs as soon as possible after they occur and before
they get a chance to burn in and cook solid. In the event of a spill-over,
follow these steps:
1. Allow the burner and grate to cool to a safe temperature level.
2. Lift off the burner grates.
3. Remove the burner cap and clean per instructions below.
4. Wipe up any spills which remains on the sealed top surface.
5. Wash the grates and burner caps in hot, soapy water and rinse
clean.
6. Replace burner cap and grate after drying thoroughly.
If ports on the burners are clogged, clean with a straight pin. Do not
enlarge or disort the ports. Do not use a toothpick to clean the ports.
Make sure burner cap is level. Occasionally check the burner for proper
size and shape. If flames lift off ports, are yellow, or are noisy when
turned on, you may need to clean the burners or call a qualified
technician for adjustments.
Sealed Burner Aluminum Base (If applicable)
The aluminum base should be wiped regularly with hot soapy water at
the end of each cooling period.
Do not use steel wool, abrasive cloths,
cleanser, or powders. To remove encrusted materials, soak the area with
at hot towel to loosen the material, then use a wooden or nylon spatula.
Do not use a metal knife, spatula, or any other material tool to scrape the
aluminum base.
NOTE: For stubborn stains, use non-abrasive cleanser such as Bon Ami TM
and a soft brush or soft Scoth Brite
TM
pad.