P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
A. Setting the Clock Time
Note:
Either the
+
or
-/CANCEL
button MUST be pressed at least once prior to leaving the set time mode. The clock
will then start to run the moment you leave the set time mode, allowing you to synchronize the
CTG-1
with your build-
ing clocks.
B. Setting the Day of the Week
Connect the
CTG-1
between your phone system and your paging amplifier as shown in the diagram below. The factory
installed rechargeable 9V battery will maintain the clock time for over 8 hours.
IMPORTANT: The CTG-1 leaves the factory with the battery backup DIP switch turned OFF to avoid discharging
the battery during shipment. The battery backup DIP switch MUST be set to ON (see Programming section J) to
maintain clock time during a power outage.
1 2 3 4 5 6 7 8 9 10
PAGING - LOUD RINGING
AMPLIFIER SYSTEM
VIKING
ELECTRONICS
HUDSON, WI 54016
VIKING
©
MODEL PA-2A
POWER 13.8
V
AC
1
2
3
4
5
6
7
8
9 10
NIGHT
TRANSFE
R
PA
G
ING
HORN
600 OHM
AUDIO OU
T
TRUNK OR
P
AGING P
ORT
DR
Y
CONT
ACT
CLOSURE
IN
PAGING
VOLUME
RINGING
VOLUME
MAX
MIN
MAX
MIN
1 - 3
4 - 6
RINGING LINES
AUDIO LOADING
TALK BATTERY
ALERT TONE
WARBLE / CHIME
1 2 3 4 5
PM
TIME
/ CANCEL
-
+
MODE
ALERT TONES
SINGLE
DOUBLE
TRIPLE
VIKING
©
MODEL CTG-1
LOCK
SET DAY
SET TIME
SET EVENTS
REVIEW/CANCEL
CLOCK CONTROLLED
TONE GENERATOR
VOL
9V BATTERY
BACKUP
1 2 3 4 5 6 7 8 9 10 11 12
Paging port
output of
PABX/KSU
PA-2A Paging/Loud Ringing
Amplifier System
Input of
Paging Amp
-or-
Common
Siren
Evacuation Signal
Doorbell
Dry Contact Closures from Alarm
Equipment, Doorbell Switch, Etc.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Step 1.
Press the
MODE
button repeatedly until the
SET TIME
indicator lights.
Step 2.
Increase or decrease the clock time by pressing the
+
or
-/CANCEL
button until the desired time is displayed.
Step 3.
Leave the set time mode by pressing the
MODE
button.
Note:
This step is only required if you want to turn off the Alert Tones on certain days of the week.
Step 1.
Press the
MODE
button repeatedly until the
SET DAY
indicator lights.
Step 2.
A flashing “
A
” indicates all 7 days of the week are “
on
” and today’s day has not been set. The day of the week has
already been set if a flashing number (
1-7
) and “
on
” or “
of
” are displayed.
Step 3.
Select today’s day of the week using the
TIME
(
+
and
-/CANCEL
) buttons. As a general rule, Sunday is day 1 and
Saturday is day 7. When today’s day of the week is flashing on the display, set it by pressing the
DOUBLE
alert tone
button. Today’s day number and “
on
” will now be displayed.
Note:
The day of the week setting and turning the alert tones off on specific days of the week is a one time set up and does not
need to be reset unless you have experienced a brown out long enough to discharge the 9V battery backup (approximately 8 hours).
To reset the day of the week and turn off tones on specific days of the week, you must power down the
CTG-1
, set DIP switch 1 to
OFF
, power up the
CTG-1
and repeat steps 1-3 above. If you had alert tones turned off on specific days of the week, repeat steps
1-4 in section
C
. When finished, set DIP switch 1 back to
ON
.
4
