4
Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or
damage the finish and void the warranty.
MAINTENANCE
ASSEMBLY
REQUIRED TOOLS
Adjustable wrench
Allen key - supplied (to remove cartridge if needed)
Plumber's putty - optional
Pipe tape
Flat screwdrivers
SAFETY TIPS
If you use soldering for the installation of the faucet, the seats, cartridges and
washers will have to be removed before using flame. Damage caused by
improper soldering will void the warranty.
Protect your eyes with safety glasses when cutting or soldering water supply
lines.
IMPORTANT POINTS
Prior to beginning installation, turn off the cold and hot water lines and open the
hot and cold knobs on the old faucet to release pressure.
When installing your new faucet, turn the connector nuts finger-tight, then use
one wrench to anchor the fitting and a second wrench to tighten the nut.
Connections that are too tight will reduce the integrity of the system and
potentially cause product failure which could lead to water damage.
Wrap all threaded connections with pipe tape available at your local hardware or
plumbing supply store. Always wrap in a clockwise direction.
Not all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT AND COLD WATER
SUPPLY LINES that are or will be connected to the new faucet to remove scale,
solder or their impurities which could damage the faucet and potentially void the
warranty.
INSTALLATION
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
4
3
6
2
1
1. SHUT OFF WATER SUPPLY. REMOVE THE OLD FAUCET
AND FLEXIBLE HOSES. CLEAN SINK SURFACE WITH A NON
ABRASIVE CLEANER IN PREPARATION FOR THE NEW FAUCET.
ENSURE THAT YOU USE PIPE TAPE
AND DO NOT OVER TIGHTEN THE
SUPPLY LINE NUTS AS THIS COULD
CAUSE PRODUCT FAILURE LEADING
TO WATER DAMAGE.
!
2. THREAD FEMALE END OF METAL BRAIDED HOSE TO THE
FAUCET (2).
7. AFTER INSTALLATION IS COMPLETE, TURN ON THE WATER
SUPPLY AND ALLOW BOTH HOT AND COLD WATER TO RUN
SEPARATELY FOR AT LEAST TWO MINUTE EACH. WHILE
WATER IS RUNNING, CHECK FOR LEAKS. IT IS IMPORTANT TO
VIEW THE CONNECTIONS AT THE MALE AND FEMALE FLEXIBLE
HOSE CONNECTIONS. IF LEAKS ARE DETECTED, REFER BACK
TO THE INSTRUCTIONS AND ADJUST ACCORDINGLY.
TIGHTENING NUTS SLIGHTLY MAY STOP ANY MINOR LEAKS.
6. ATTACH THE FEMALE CONNECTIONS OF THE FLEXIBLE
HOSES TO THE COLD AND HOT WATER SUPPLY .
5. (IF NOT DONE ALREADY) ATTACH SPRAYER TO FEMALE
CONNECTION OF SPRAYER HOSE BY HAND AND TIGHTEN
UNTIL SECURE. MAKE SURE THE BLACK WASHER WITH
SCREEN IS SEATED AND INSTALLED PROPERLY.
!
ENSURE THAT PARTS ARE
ASSEMBLED IN THE ORDER AS
DEPICTED IN DIAGRAM TO PREVENT
DAMAGE TO FAUCET AND SUPPLY
LINES.
3. POSITION THE FAUCET IN THE COUNTERTOP HOLE, FROM
BENEATH THE COUNTERTOP HOLE ASSEMBLE THE SMALLER
RUBBER RING, THE LARGER RUBBER RING, AND THE METAL
RING IN THE ORDER DEPICTED IN THE DIAGRAM. THEN
THREAD METAL NUT ONTO HOLLOW PIN. TIGHTEN THE METAL
NUT UNTIL FAUCET IS SECURE.
4. SCREW SPRAY HOSE TO THE COPPER PIN (THE LONGEST
PIN). MAKE SURE TO HAVE A TIGHT SEAL USING ADJUSTABLE
WRENCH. ATTACH SUPPLIED COUNTERWEIGHT TO THE HOSE.
!
ENSURE THAT YOU USE PIPE TAPE AND ADJUSTABLE WRENCH,
DO NOT OVER TIGHTEN AS THIS COULD CAUSE PRODUCT
FAILURE LEADING TO WATER DAMAGE.
DO NOT OVER TIGHTEN CONNECT POINT AS THIS COULD
CAUSE PRODUCT FAILURE LEADING TO WATER DAMAGE
!
NUT
RUBBER RING
ALLEN KEY (REMOVES HANDLE
TO ACCESS CARTRIDGE)
TWO METAL
BRAIDED HOSES
NUT
COUNTERWEIGHT
METAL RING
RUBBER RING
FAUCET
ASSEMBLY
PACKAGE CONTENTS
!
USE WASHER WITH SCREEN AT CONNECTION POINT BETWEEN SPRAYER
AND SPRAYER HOSE. THIS WILL STOP DEBRIS FROM TRAVELING INTO THE
SPRAYER HEAD AND EFFECTING ITS FUNCTIONALITY. PLEASE NOTE THAT
THE SCREEN WASHER WILL NEED TO BE REMOVED AND CLEANED
APPROXIMATELY ONCE EVERY 3 MONTHS TO AVOID BUILD UP AND LOW
WATER FLOW.
