Viglen Vig660W Скачать руководство пользователя страница 7

Страница: 7 / 51

V1.0 Vig660W Motherboard Manual

Rear I/O Ports



1 x 12V-19V Power Port



1x D-Sub (VGA)



1x HDMI



1x Gigabit LAN (Intel LAN PHY)



1x Microphone



1x Headphone/Speaker



4x USB 3.0 Ports

Internal Connectors



1 x Front Panel Connector



1 x 4-pin Chassis Speaker Connector



1x Front panel Audio Connector (2x5 pin)



1 x Front Panel Audio Connector (2 x 5 pin)



2 x USB 2.0 Connector Support 4 x USB 2.0 Ports (2 x 5 pin)



1x USB 2.0 Connector Supports 1x USB 2.0 Port (1x5 pin)



2 x SATA 6Gb/s Ports



1 x 4-pin CPU Fan Connector



1 x 4-pin ATX 12V/19V Power Connector



1 x 4-pin SATA Power_HDD Connector



1 x 3-pin SATA Power_ODD Connector



1 x 3-pin Clear CMOS Header



1 x Clear CMOS Jumper

Expansion Capabilities



·1x mini PCIE full card slot,support Intel® 310 series SSD cards or others with same pin define



·1x mini PCIE half card slot,support 802.11a/b/g/n WIFI and Bluetooth 3.0+HS

TPM



Nuvoton® NPCT420B TPM IC on board, support TPM 1.2

BIOS



AMI EFI BIOS

Intel® vPRO

Technology



Intel® Advanced Mangement Technology (Intel® AMT) 8.0



Intel® Trusted Execution Technology (Intel® TXT)



Intel® Virtualization Technology (Intel® VT)



Intel® Virtualization for Directed I/O(Intel® VT-d)



KVM Remote Control

Содержание Vig660W




















































Результаты поиска

Содержание Vig660W

Отзывы:

Похожие инструкции для Vig660W

Бренды по названию

Популярные бренды

Viglen Vig660W, Руководство пользователя

Результаты поиска

Содержание Vig660W

Отзывы:

Похожие инструкции для Vig660W

Бренды по названию

Популярные бренды