Viglen Vig660W Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 51

background image

V1.0 Vig660W Motherboard Manual

23

Serial ATA Connector: SATA1 ~ SATA1

This connector is a high-speed Serial ATA interface port. Each connector can connect to
one Serial ATA device.

Figure 11

: Serial ATA Connector

NOTE:

Please do not fold the serial ATA cable into 90-degree angle. Otherwise, data loss may
occur during transmission.



Power Supply Connectors

The board has the following power supply connectors:

•

External Power Supply

– the board can be powered through a 19 V DC connector on

the back panel. The back panel DC connector is compatible with a 7.4 mm/OD (outer
diameter) and 5.1 mm/ID (inner diameter) plug, where the inner contact is +19 (±10%) V
DC and the shell is GND. The maximum current rating is 12 A.

«
...
22
23
24
25
26
...
»

Содержание Vig660W




















































Отзывы:

Нет отзывов

Похожие инструкции для Vig660W

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 24

Бренд: IEI Technology Страницы: 126

Бренд: ON Semiconductor Страницы: 5

Бренд: ASROCK Страницы: 221

PCM-8152 3rd Generation

Бренд: Aaeon Страницы: 6

conga-HPC/EVAL-Server

Бренд: Congatec Страницы: 54

Бренд: JETWAY Страницы: 47

Бренд: Wemos Страницы: 12

Бренд: Evalue Technology Страницы: 91

Бренд: Infineon Страницы: 30

Freescale MCIMX6Q-SL

Бренд: NXP Semiconductors Страницы: 37

Бренд: ON Semiconductor Страницы: 2

Бренд: JETWAY Страницы: 47

Бренд: Gigabyte Страницы: 75

KIT34704BEPEVBE

Бренд: NXP Semiconductors Страницы: 39

Бренд: CDI Страницы: 4

Бренд: Fujitsu Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды