Viglen D945GTP Скачать руководство пользователя страница 6

Страница: 6 / 16

LGA775 processor socket

Front panel USB connectors

Intel 82945G GMCH

Chassis intrusion connector

Processor fan connector

Intel 82801G I/O Controller Hub (ICH7)

DIMM Channel A sockets

SPI Flash device “Firmware Hub (FWH)”

DIMM Channel B sockets

IEEE1394a controller not fitted optional

SCSI LED connector (optional)

IEEE1394a connectors not fitted
optional

I/O controller

Speaker

•

Back Panel Connectors

Figure 2.

Back Panel Connectors.

Table 3.

Item

Description

PS/2* mouse port (Green)

PS/2 keyboard port (Purple)

Serial port A (Teal)

Parallel port (Burgundy)

VGA port

USB ports (two)

LAN

USB ports (two)

Audio line out/Retasking Port D
(Lime Green)

Mic in/Retasking Port B (Pink)

Audio line in/Retasking Port C
(Light Blue)

Note:

The back panel audio line out connector is designed to power headphones or amplified

speakers only. Poor audio quality occurs if passive (non-amplified) speakers are connected to this
output.

Page 6 of 17

Содержание D945GTP

















Результаты поиска

Содержание D945GTP

Отзывы:

Похожие инструкции для D945GTP

Бренды по названию

Популярные бренды

Viglen D945GTP, Быстрый старт

Результаты поиска

Содержание D945GTP

Отзывы:

Похожие инструкции для D945GTP

Бренды по названию

Популярные бренды