ViewSonic VX910 - 19" LCD Monitor Скачать руководство пользователя страница 4

Страница: 4 / 56

Caution :

No modification of any circuit should be attempted . Service work should only be performed after you

are thoroughly familiar with all of the following safety checks and servicing guide line

Safety Check :

Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter

circuit. These voltage are exposed in such areas as the associated transformer circuits .

POWER SUPPLY REQUIREMENTS

The internal power converter for this display utilizes AC and DC cords , AC cord is detachable , but DC

cord is permanently attached . Any attempt to replace another power board could result in serious problem

on the display .

LEAKAGE CURRENT HOT CHECK

4-1 Plug the AC cord directly into the AC outlet. Do not use an isolation transformer during this check.

4-2 Connect a 1500 ohm , 10 watt resistor , paralleled by a 0.15uF capacitor between each metallic part

and a good earth ground

4-3 Use an AC voltmeter with 1000 ohm / volt or more sensitivity and measure the AC voltage across

the combination 1500 ohm resistor and 0.15uF capacitor.

4-4 Move the resistor connection to each exposed metallic part and measure the voltage.

4-5 Reverse the polarity of the AC plug in the AC outlet and repeat the above measurement.

4-6 Voltage measured must not exceed 1.5 volt RMS, from any exposed metallic part to the ground. A

leakage current tester may be used in the above hot check, in which case any circuit measured must

not exceed 1.0 milliamp. In the case of a measurement exceeding the 1.0 milliamp value, a rework

is required to eliminate the chance of a shock hazard .

To Metal Parts

AC VOLTMETER

1500

10W

0.15u

Earth Ground

1. Precautions and Safety Notices

ViewSonic

Corporation

nfidential

Not

Copy

VX910

Содержание VX910 - 19" LCD Monitor

























































Результаты поиска

Содержание VX910 - 19" LCD Monitor

Отзывы:

Бренды по названию

Популярные бренды

ViewSonic VX910 - 19" LCD Monitor, Руководство по обслуживанию

Результаты поиска

Содержание VX910 - 19" LCD Monitor

Отзывы:

Бренды по названию

Популярные бренды