manualshive.com logo in svg

ViewSonic VX910 - 19" LCD Monitor, Руководство по обслуживанию

Поделиться
Скачать
ViewSonic VX910 - 19

                         

Press “[1]” Button to exit Fine tune item. 

                         

Press 

“

[

▲

]

”

 Button to make current item high. 

                         

Press “[

▼

]“Button to make current item low. 

 

4)

 

Sharpness Item 

                         

Press “[2]” Button to enter Sharpness item. 

                         

Press “[1]” Button to exit Sharpness item. 

                         

Press 

“

[

▲

]

”

 Button to make current item high. 

                         

Press “[

▼

]“ Button to make current item low. 

 

(6)

 

Setup Menu Page: 

                        

 Press “[2]” Button to enter Setup Menu page.    

                         

Press “[1]” Button to exit Setup Menu page. 

                         

Press 

“

[

▲

]

”

Button to the previous item or “[

▼

]“ Botton to the next item. 

1)

 

Language Select Item 

                               

Press “[2]”Button to enter Language Select item.    

                               

Press “[1]” Button to exit Language Select item. 

Press 

“

[

▲

]

”

 Button to the previous option or “[

▼

]“ Botton to the next option.

 

 

English,French… … ..Option

 

Press “[2]” Button to select the language. 

Press “[1]” Button to exit the option. 

2)

 

Resolution Notice Item 

                               

Press “[2]” Button to enter Resolution Notice item.    

                               

Press “[1]” Button to exit Resolution Notice item. 

      Enable,Disable Option 

                               

Press “[2]” Button to select the option.   

                               

Press “[1]” Button to exit the option 

Press 

“

[

▲

]

”

 Button to the previous option or “[

▼

]“ Botton to the next   

option.                           

 

3)

 

OSD Position Item 

                               

Press “[2]” Button to enter OSD Position item.    

Press “[1]” Button to exit OSD Position item. 

a)

 

Horizontal Position Option 

              Press “[2]” Button to enter the Vertical Position option.  

       Press “[1]” Button to exit Horizontal Position option. 

                                           Press 

“

[

▲

]

”

 Button to make current option high. 

       Press “[

▼

]“ Button to make current option low 

 

 

 

24

ViewSonic 

Corporation 

Co

nfidential

 

- 

Do 

Not 

Copy 

 

 

 

VX910

Содержание VX910 - 19" LCD Monitor

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды