background image

Disclaimer and Warning

Legends

1.1 Introduction

1.Product Introduction

1.

Important Note

Warning

D3535 is a high-precision 2-axis gimbal integrated with a 4000lm 

luminous flux searchlight. It supports yaw/pitch control, home 

position, gimbal speed adjustment and light on/off. The 2 axis gimbal 

can achieve stabilization in yaw and pitch, the integrated design of 

damping system and gimbal can greatly reduce mechanical 

vibration.

It has an operating range of up to 150m and widely used at night or 

in utter poor light environment for users in night surveillance, 

emergency response/search and rescue, fire fighting……

Congratulations on purchasing your new Viewpro product. Please 

read this entire document carefully. Failure to read or follow instruc-

tions and warnings in this document may result in damage to your 

Viewpro product. Disassemble the gimbal camera by user is not 

permitted, as which may cause the camera does not work normally.
Viewpro accepts no liability for damage, injury or any legal responsi-

bility incurred directly or indirectly from the use of this project. The 

user shall observe safe and lawful practices including, but no limited 

to, those set forth in the manual.

Содержание D3535


















Отзывы: